[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Paparazzi-devel] No throttle in Auto2
From: |
cory barton |
Subject: |
Re: [Paparazzi-devel] No throttle in Auto2 |
Date: |
Thu, 21 Aug 2008 16:59:52 -0400 |
So I disconnected the rf modems, and tried using the ftdi cable, but
the behavior is exactly the same. I think based on the experience with
the usb modem that the gcs is not sending any messages. I am looking
for a way to watch the outgoing messages, but if anyone knows how,
please let me know.
Cory
On Thu, Aug 21, 2008 at 4:45 PM, cory barton <address@hidden> wrote:
> Ok, I am outside with it now, and apparently, the ground station is
> not sending anything. I have the USB modem, and its status lights
> indicate that it is receiving constantly from the plane, but is not
> sending anything. The modem is in its default configuration.
>
> Is there any way to watch the outgoing messages from the groundstation
> to the plane?
>
> Thanks,
>
> Cory
>
> On Thu, Aug 21, 2008 at 4:05 PM, address@hidden <address@hidden> wrote:
>> Does your plane respond to modem commands? Maybe it's just not getting the
>> launch command? Try changing the tuning gains and see if the values update.
>>
>> -- "cory barton" <address@hidden> wrote:
>> Hello,
>>
>> I have done the ground based portion of the tuning procedure and
>> everything is going mostly ok. My one issue is that the motor will not
>> run in AUTO2 mode.
>>
>> I think that a good thing to try before flying is to get a good grip
>> on the plane, and verify that the plane will throttle up, when the
>> flight plan is in the takeoff block, and the launch button is pressed.
>>
>> I am using a modified version of the basic flight plan(see below). I
>> have eliminated everything except the takeoff, and blocks to circle
>> around STDBY, and waypoint 1. It works great in simulation.
>>
>> When I turn on the AP, I have control of all the actuators in manual
>> mode, including throttle. The PFD reflects the actual attitude of the
>> plane. I also have full control in AUTO1 mode, and the control
>> surfaces appear to move correctly when I change the attitude of the
>> plane, and the throttle response is good.
>>
>> However, when I switch to AUTO2, I cannot get the system to move out
>> of the holding point block, and the throttle area is red in the GCS. I
>> got a message in the GCS saying: "mayday, kill mode". I tried using
>> the settings under the misc tab to set kill_throttle to 0, but it
>> didn't work. No matter what I tried, I could not get the prop to spin
>> in AUTO2 mode.
>>
>> Then I commented out the holding point block, and reflashed the AP.
>> The flight plan went directly from Geo init to takeoff, and the
>> throttle area was orange in the GCS. So I set the AP to AUTO2, and hit
>> the launch button. No response. I switched back to manual and auto1,
>> and the throttle works just fine. Switch to AUTO2, and no throttle.
>>
>> Please let me know what I am missing.
>>
>> Thanks,
>>
>> Cory
>>
>> <!DOCTYPE flight_plan SYSTEM "flight_plan.dtd">
>>
>> <flight_plan alt="75" ground_alt="0" lat0="37.08253" lon0="-76.39815"
>> max_dist_from_home="700" name="Basic" security_height="25">
>> <header>
>> #include "nav_line.h"
>> #include "datalink.h"
>> </header>
>> <waypoints>
>> <waypoint name="HOME" x="0" y="0"/>
>> <waypoint name="STDBY" x="120.6" y="115.6"/>
>> <waypoint name="1" x="-45.5" y="174.2"/>
>> <waypoint name="CLIMB" x="153.6" y="23.9"/>
>> </waypoints>
>> <exceptions/>
>> <blocks>
>> <block name="Wait GPS">
>> <set value="1" var="kill_throttle"/>
>> <while cond="!GpsFixValid()"/>
>> </block>
>> <block name="Geo init">
>> <while cond="LessThan(NavBlockTime(), 10)"/>
>> <call fun="NavSetGroundReferenceHere()"/>
>> </block>
>> <!--
>> <block name="Holding point">
>> <set value="1" var="kill_throttle"/>
>> <attitude roll="0" throttle="0" vmode="throttle"/>
>> </block>
>> -->
>> <block name="Takeoff" strip_button="Takeoff (wp CLIMB)"
>> strip_icon="takeoff.png">
>> <exception cond="estimator_z > ground_alt+25" deroute="Standby"/>
>> <set value="0" var="kill_throttle"/>
>> <set value="0" var="estimator_flight_time"/>
>> <go from="HOME" pitch="15" throttle="1.0" vmode="throttle" wp="CLIMB"/>
>> </block>
>> <block name="Standby" strip_button="Standby" strip_icon="home.png">
>> <circle radius="nav_radius" wp="STDBY"/>
>> </block>
>> <block name="Circle 1" strip_button="Circle 1"
>> strip_icon="circle-right.png">
>> <circle radius="nav_radius" wp="1"/>
>> </block>
>> </blocks>
>> </flight_plan>
>>
>>
>> _______________________________________________
>> Paparazzi-devel mailing list
>> address@hidden
>> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>
>>
>> ____________________________________________________________
>> Click here for a free directory of employee development and training
>> solutions.
>> http://thirdpartyoffers.juno.com/TGL2141/fc/Ioyw6i3l7kPMi4YHqc5HYNF75sjUbHdQ217hUDCKDGLam3lCjKMAwF/
>>
>>
>> _______________________________________________
>> Paparazzi-devel mailing list
>> address@hidden
>> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>
>
- [Paparazzi-devel] No throttle in Auto2, cory barton, 2008/08/20
- Re: [Paparazzi-devel] No throttle in Auto2, Uttam Chandrashekhar, 2008/08/20
- Re: [Paparazzi-devel] No throttle in Auto2, address@hidden, 2008/08/21
- Re: Re: [Paparazzi-devel] No throttle in Auto2, Martin Mueller, 2008/08/21
- Re: Re: [Paparazzi-devel] No throttle in Auto2, address@hidden, 2008/08/22
- Re: [Paparazzi-devel] No throttle in Auto2, David Buzz Carlson, 2008/08/22
- Re: [Paparazzi-devel] No throttle in Auto2, Pascal Brisset, 2008/08/22
- Re: [Paparazzi-devel] No throttle in Auto2, cory barton, 2008/08/22
- Re: [Paparazzi-devel] No throttle in Auto2, Bernard Davison, 2008/08/22
- Re: [Paparazzi-devel] No throttle in Auto2, cory barton, 2008/08/22
- Re: [Paparazzi-devel] No throttle in Auto2, Bernard Davison, 2008/08/22