Send Paparazzi-devel mailing list submissions to
address@hiddenTo subscribe or unsubscribe via the World Wide Web, visit
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
or, via email, send a message with subject or body 'help' to
address@hidden
You can reach the person managing the list at
address@hidden
When replying, please edit your Subject line so it is more specific
than "Re: Contents of Paparazzi-devel digest..."
Today's Topics:
1. Re: ADC channel for Gyro (C Kuo)
2. need help with tunnel loading (Prashanth Thankachan)
3. Re: ADC channel for Gyro (David Conger)
4. Re: ADC channel for Gyro (Michel GORRAZ)
5. Re: ADC channel for Gyro (David Conger)
----------------------------------------------------------------------
Message: 1
Date: Mon, 23 Jun 2008 17:05:21 +0100
From: C Kuo <address@hidden>
Subject: Re: [Paparazzi-devel] ADC channel for Gyro
To: address@hidden, Michel GORRAZ
<address@hidden>
Cc: address@hidden
Message-ID: <address@hidden>
Content-Type: text/plain; charset=ISO-8859-1
Hi Michel
Thanks for the advice, I will order the gyro and do some modification.
Thanks
Chen
Quoting Michel GORRAZ <address@hidden>:
Hi,
For sure, you can use this ADC with a Gyro (or other analog sensor) but
this is a 3.3v max input level, so if your gyro is a 5v, don't forget the
resistor bridge...or use ADC5 or ADC6 : these inputs have their own
on-board resistor bridge.
@+
Michel
2008/6/23 C Kuo <address@hidden>:
Hi guys
I was wondering, on the "USB" port on TinyV2 has a ADC_7, could I use
this
chaneel for connecting roll gyro?
Thanks
Chen
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
------------------------------
Message: 2
Date: Mon, 23 Jun 2008 22:26:34 +0530
From: "Prashanth Thankachan" <address@hidden>
Subject: [Paparazzi-devel] need help with tunnel loading
To: address@hidden
Message-ID:
<address@hidden>
Content-Type: text/plain; charset="iso-8859-1"
Hi all
This is my first post and a request for help...Have been with the paparazzi
AP stuff for awhile now on the wiki and the archives and finally managed to
get one and thought to get to configuring the zillion steps one by one....
started to load the tunnel to configure the GPS and here is my first
hurdle...
Connected to the USB header on the AP, powered the AP, and in a terminal
window gave the command
make AIRCRAFT=MJ5 tunnel.upload
The only response I get is
make: *** No rule to make target `tunnel.upload'. Stop.
I tried the same from the paparazzi center and the same error
BUILD TJ1
make[1]: Entering directory `/home/prashanth/paparazzi3'
make[1]: Nothing to be done for `all_ac_h'.
make[1]: Leaving directory `/home/prashanth/paparazzi3'
cd sw/airborne; make PAPARAZZI_SRC=/home/prashanth/paparazzi3
PAPARAZZI_HOME=/home/prashanth/paparazzi3 TARGET=tunnel all
make[1]: Entering directory `/home/prashanth/paparazzi3/sw/airborne'
Makefile:40: ../../conf/Makefile.: No such file or directory
make[1]: *** No rule to make target `../../conf/Makefile.'. Stop.
make[1]: Leaving directory `/home/prashanth/paparazzi3/sw/airborne'
make: *** [tunnel.compile] Error 2
make: Leaving directory `/home/prashanth/paparazzi3'
Many thankx in advance for any any help in this direction
Prashanth
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.gnu.org/pipermail/paparazzi-devel/attachments/20080623/50ea3132/attachment.html
------------------------------
Message: 3
Date: Mon, 23 Jun 2008 09:40:26 -0700
From: David Conger <address@hidden>
Subject: Re: [Paparazzi-devel] ADC channel for Gyro
To: address@hidden
Message-ID: <address@hidden>
Content-Type: text/plain; charset="us-ascii"
Hello,
Thank you Michel. GTK. Can I ask a question related...
My Gyro is 5v (ADXRS300) with ST1, ST2, TEMP, 2.5V, RATE, GND, 5V..
Can someone please give the pins to connect to the Tiny on ADC2?
5v is easy -> +5v on Tiny
GND -> GND on Tiny
....
Without any instructions on the Wiki about the connector and going by
the funjet1.xml airframe file given I had it connected to ADC1
GRYO ---- TINY
GND -> GND
RATE->ADC3
5V->+5v
I hope I didn't damage ADC1 on the Tiny
Thank you,
-David
So, if I were to connect my 5v Gyro into
On Jun 23, 2008, at 8:29 AM, Michel GORRAZ wrote:
Hi,
For sure, you can use this ADC with a Gyro (or other analog sensor)
but this is a 3.3v max input level, so if your gyro is a 5v, don't
forget the resistor bridge...or use ADC5 or ADC6 : these inputs
have their own on-board resistor bridge.
@+
Michel
2008/6/23 C Kuo <address@hidden>:
Hi guys
I was wondering, on the "USB" port on TinyV2 has a ADC_7, could I
use this
chaneel for connecting roll gyro?
Thanks
Chen
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.gnu.org/pipermail/paparazzi-devel/attachments/20080623/db01373f/attachment.html
------------------------------
Message: 4
Date: Mon, 23 Jun 2008 21:57:27 +0200
From: "Michel GORRAZ" <address@hidden>
Subject: Re: [Paparazzi-devel] ADC channel for Gyro
To: address@hidden
Message-ID:
<address@hidden>
Content-Type: text/plain; charset="iso-8859-1"
Hi,
The easiest way to connect a ADXRS300 on a Tiny v2 (or a Twog) is to use
ADC5 on the "ADC2" connector
- GND on GND (pin #1)
- +5V on +5v (pin #2)
- Rateout on ADC5 (pin #5) => resistor bridge for 5v sensor is included for
this ADC on the Tiny V2
And... that all !
Don't worry, ADC1 is probably alive :)
@+
Michel
2008/6/23 David Conger <address@hidden>:
Hello,
Thank you Michel. GTK. Can I ask a question related...
My Gyro is 5v (ADXRS300) with ST1, ST2, TEMP, 2.5V, RATE, GND, 5V..
Can someone please give the pins to connect to the Tiny on ADC2?
5v is easy -> +5v on Tiny
GND -> GND on Tiny
....
Without any instructions on the Wiki about the connector and going by the
funjet1.xml airframe file given I had it connected to ADC1
GRYO ---- TINY
GND -> GND
RATE->ADC3
5V->+5v
I hope I didn't damage ADC1 on the Tiny
Thank you,
-David
So, if I were to connect my 5v Gyro into
On Jun 23, 2008, at 8:29 AM, Michel GORRAZ wrote:
Hi,
For sure, you can use this ADC with a Gyro (or other analog sensor) but
this is a 3.3v max input level, so if your gyro is a 5v, don't forget the
resistor bridge...or use ADC5 or ADC6 : these inputs have their own
on-board resistor bridge.
@+
Michel
2008/6/23 C Kuo <address@hidden>:
Hi guys
I was wondering, on the "USB" port on TinyV2 has a ADC_7, could I use
this
chaneel for connecting roll gyro?
Thanks
Chen
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.gnu.org/pipermail/paparazzi-devel/attachments/20080623/905b0166/attachment.html
------------------------------
Message: 5
Date: Mon, 23 Jun 2008 13:29:20 -0700
From: David Conger <address@hidden>
Subject: Re: [Paparazzi-devel] ADC channel for Gyro
To: address@hidden
Message-ID: <address@hidden>
Content-Type: text/plain; charset="us-ascii"
Excellent,
Thank you Michel,
Also THANK YOU! ... for taking such time to document the designs so
well on the Wiki.
When I first started my interest with Paparazzi Tiny1.3 was new...BOM,
Pinout, even photos were scarce. I use your Wiki pages exclusively and
many many times a day to refer to the pinouts, layouts etc. Questions
asked of me are most often replied with URL right to your pages to the
pinouts or images or notes.
Well done. I'm sure many many people appreciate the time you spent to
document so thoroughly. I may not find what I am looking for on the
Wiki but I have to at the same time give credit that the latest
designs are extremely well documented there.
Regards,
David
On Jun 23, 2008, at 12:57 PM, Michel GORRAZ wrote:
Hi,
The easiest way to connect a ADXRS300 on a Tiny v2 (or a Twog) is to
use ADC5 on the "ADC2" connector
- GND on GND (pin #1)
- +5V on +5v (pin #2)
- Rateout on ADC5 (pin #5) => resistor bridge for 5v sensor is
included for this ADC on the Tiny V2
And... that all !
Don't worry, ADC1 is probably alive :)
@+
Michel
2008/6/23 David Conger <address@hidden>:
Hello,
Thank you Michel. GTK. Can I ask a question related...
My Gyro is 5v (ADXRS300) with ST1, ST2, TEMP, 2.5V, RATE, GND, 5V..
Can someone please give the pins to connect to the Tiny on ADC2?
5v is easy -> +5v on Tiny
GND -> GND on Tiny
....
Without any instructions on the Wiki about the connector and going
by the funjet1.xml airframe file given I had it connected to ADC1
GRYO ---- TINY
GND -> GND
RATE->ADC3
5V->+5v
I hope I didn't damage ADC1 on the Tiny
Thank you,
-David
So, if I were to connect my 5v Gyro into
On Jun 23, 2008, at 8:29 AM, Michel GORRAZ wrote:
Hi,
For sure, you can use this ADC with a Gyro (or other analog
sensor) but this is a 3.3v max input level, so if your gyro is a
5v, don't forget the resistor bridge...or use ADC5 or ADC6 : these
inputs have their own on-board resistor bridge.
@+
Michel
2008/6/23 C Kuo <address@hidden>:
Hi guys
I was wondering, on the "USB" port on TinyV2 has a ADC_7, could I
use this
chaneel for connecting roll gyro?
Thanks
Chen
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.gnu.org/pipermail/paparazzi-devel/attachments/20080623/8d874273/attachment.html
------------------------------
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
End of Paparazzi-devel Digest, Vol 51, Issue 30
***********************************************