paparazzi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] Re: Can you please share your Tiny1.3 Gerber File?


From: Uttam Chandrashekhar
Subject: Re: [Paparazzi-devel] Re: Can you please share your Tiny1.3 Gerber File?
Date: Wed, 5 Dec 2007 23:28:02 -0800 (PST)

Hi Pascal,

Thanks so much, will let you know how it goes. :)



----- Original Message ----
From: Pascal Brisset <address@hidden>
To: address@hidden
Sent: Thursday, December 6, 2007 12:35:53 PM
Subject: Re: [Paparazzi-devel] Re: Can you please share your Tiny1.3 Gerber File?

More updates: the default configuration has been modified, so please

cvs update
rm conf/conf.xml conf/control_panel.xml (IF you have not already created
any new aircraft or session)
make
./paparazzi

The Simulation page in the wiki also has to be updated ... soon.

--Pascal

Pascal Brisset wrote:
> Hi Uttam,
>
> hmmmm, the README file is out of date. A new one has just been
> commited. The "make demo" technique is also out of date:
>
>  1) "make" in the top directory to compile all the tools.
>
>  2) "./paparazzi" to run the Paparazzi Center
>
>  3) Select the "MJ5" or the "TJ1" aircraft in the upper-left A/C
> combo box. Select "sim" from upper-middle "target" combo box. Click
> "Build". When the compilation is finished, select "Simulation" from
> the upper-right session combo box and click "Execute".
>
>  4) In the GCS, wait about 10s for the aircraft to be in the "Holding
> point" navigation block. Switch to the "Takeoff" block (lower-left
> blue airway button in the strip). Takeoff with the green launch button.
>
>
> Note for "old" users: When the Paparazzi Center is used, there is
> usually no need to set the environment variables (PAPARAZZI_SRC and
> PAPARAZZI_HOME).
>
> --Pascal
>
>
> Uttam Chandrashekhar wrote:
>> Hi guys,
>>
>> I'm typing this mail from Ubuntu! So the internet is setup, envy did
>> its job ( in manual mode though ). Paparazzi dev and arm7 packages
>> were downloaded, and the cvs source code installed. I compiled it
>> using make and then tried to see if paparazzi center started up, it
>> did. So, generally, everything here seems to be working, BUT, the
>> simulation does not run. When I say make demo, it raises an error
>> towards the end saying Twin1 cant be found in conf.xml. I looked at
>> the airframes folder, and there is no Twin1 there, and there is no
>> Twin1 mentioned in the conf.xml file either. I tried to be smart and
>> created a duplicate of one of the other airframe files and saved it
>> as Twin1. It gives the following error when I run make demo: ( only
>> the last bit gives this error )
>>
>> cd sw/airborne; make
>> PAPARAZZI_SRC=/home/dcenterprises/paparazzi/paparazzi3
>> PAPARAZZI_HOME=/home/dcenterprises/paparazzi/paparazzi3 TARGET=sim
>> ARCHI=sim all
>> CC /home/dcenterprises/paparazzi/paparazzi3/var/Twin1/sim/fw_h_ctl.o
>> fw_h_ctl.c: In function ‘h_ctl_init’:
>> fw_h_ctl.c:110: error: ‘H_CTL_COURSE_PGAIN’ undeclared (first use in
>> this function)
>> fw_h_ctl.c:110: error: (Each undeclared identifier is reported only once
>> fw_h_ctl.c:110: error: for each function it appears in.)
>> fw_h_ctl.c:112: error: ‘H_CTL_ROLL_MAX_SETPOINT’ undeclared (first
>> use in this function)
>> fw_h_ctl.c:126: error: ‘H_CTL_PITCH_PGAIN’ undeclared (first use in
>> this function)
>> fw_h_ctl.c:127: error: ‘H_CTL_PITCH_DGAIN’ undeclared (first use in
>> this function)
>> fw_h_ctl.c:129: error: ‘H_CTL_ELEVATOR_OF_ROLL’ undeclared (first use
>> in this function)
>> make[2]: ***
>> [/home/dcenterprises/paparazzi/paparazzi3/var/Twin1/sim/fw_h_ctl.o]
>> Error 1
>> make[1]: *** [sim] Error 2
>> make: *** [ac1] Error 2
>>
>> Anyone know whats happening? I understand the errors, but I don't
>> know how to fix them here!
>>
>> Thanks in advance,
>> Uttam
>>
>>
>>
>>
>> ----- Original Message ----
>> From: David <address@hidden>
>> To: Uttam Chandrashekhar <address@hidden>
>> Sent: Wednesday, December 5, 2007 5:10:26 AM
>> Subject: Re: Can you please share your Tiny1.3 Gerber File?
>>
>> Did it work with 64bit (network)?
>> "no internet" doesn't really mean bad drivers. Do you get green
>> lights on the card itself (i.e. physical connection is valid)? What
>> does: ifconfig command return?
>>
>> I have yet to have Ubuntu not install network properly. I have many
>> times had issues trying to setup wireless correctly, never driver
>> level, just getting WEP/WPA other encrypted stuff working right.
>>
>> Quite possibly this is simply settings not drivers.
>>
>> -DC
>>
>> On Dec 4, 2007, at 3:37 PM, Uttam Chandrashekhar wrote:
>>
>>> Dave,
>>>
>>> Envy sounds good. I installed the 32 bit already, and I think
>>> something is wrong with the Network interface card drivers. I simply
>>> have no internet! I spent all of yesterday trying to sort the
>>> problem, no luck :(
>>>
>>>
>>> -Uttam
>>>
>>> ----- Original Message ----
>>> From: David Conger <address@hidden
>>> <mailto:address@hidden>>
>>> To: Uttam Chandrashekhar <address@hidden
>>> <mailto:address@hidden>>
>>> Sent: Wednesday, December 5, 2007 3:46:26 AM
>>> Subject: Re: Can you please share your Tiny1.3 Gerber File?
>>>
>>> Uttam,
>>>
>>> I saw this: "Hi,
>>>
>>> Thanks. I tried the 64bit architecture and it did not recognize my
>>> NIC, or the graphic drivers. When I look at the installed devices, I
>>> see a lot of "unknowns". I am downloading the x86 version now,
>>> hopefully I can get the internet and graphics working in the x86
>>> version.
>>>
>>> -Thanks,
>>> Uttam"
>>>
>>> You should be okay with 64bit. You just have to install the 32bit
>>> compilers and libraries so you can compile it in 32 bit.
>>> I say this because on my Desktop (AMD64) I installed 64bit Ubuntu
>>> but wanted to install sound drivers that were only 32 bit. I googled
>>> and found directions to install/compile the 32 bit and it worked
>>> fine. I imagine the same would be the case for the paparazzi.
>>> Did you try "envy" it's amazing, really, just trust me if you have
>>> nVidia graphics even if Ubuntu recognizes it...you want to run
>>> Envy...trust me. It downloads the right sources based on your system
>>> then recompiles them and even sets up the X config files. I now will
>>> only use nVidia cards because I know I have Envy to do the proper
>>> setup/config.
>>> -David Conger
>>>
>>> On Dec 2, 2007 11:46 PM, Uttam Chandrashekhar
>>> <address@hidden
>>> <mailto:address@hidden>> wrote:
>>>
>>>    Hi Dave,
>>>
>>>    Sure, here you go, Gerbers attached. Our PCB's are getting made!
>>>    Please let me know if there's anything else.
>>>    -Thanks,
>>>    Best Regards,
>>>    Uttam
>>>
>>>
>>>    ----- Original Message ----
>>>    From: David Conger < address@hidden
>>>    <mailto:address@hidden>>
>>>    To: address@hidden
>>>    <mailto:address@hidden>
>>>    Sent: Monday, December 3, 2007 11:48:56 AM    Subject: Can you
>>> please share your Tiny1.3 Gerber File?
>>>
>>>    Hi Uttam,
>>>
>>>    I have been following the Paparazzi list for some time. I want to
>>>    create Gerber files but am having issues.    I was trying to
>>> follow your directions but you don't list
>>>    specifically what layers to add or what layers to check in the
>>>    layer list when editing the gerber job...
>>>
>>>    Can you please email me your gerber file you were sent? I need to
>>>    have some FAB myself and worry I will send an inappropriate file.
>>>    Best Regards,
>>>    David Conger
>>>
>>>
>>>
>>>   
>>> ------------------------------------------------------------------------
>>>
>>>    Be a better sports nut! Let your teams follow you with Yahoo
>>>    Mobile. Try it now.
>>>   
>>> <http://us.rd.yahoo.com/evt=51731/*http://mobile.yahoo.com/sports;_ylt=At9_qDKvtAbMuh1G1SQtBI7ntAcJ%0A>
>>>
>>>
>>>
>>>
>>>
>>> ------------------------------------------------------------------------
>>>
>>> Looking for last minute shopping deals? Find them fast with Yahoo!
>>> Search.
>>> <http://us.rd.yahoo.com/evt=51734/*http://tools.search.yahoo.com/newsearch/category.php?category=shopping>
>>>
>>
>>
>>
>> ------------------------------------------------------------------------
>> Be a better friend, newshound, and know-it-all with Yahoo! Mobile.
>> Try it now.
>> <http://us.rd.yahoo.com/evt=51733/*http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ%20>
>>
>> ------------------------------------------------------------------------
>>
>> _______________________________________________
>> Paparazzi-devel mailing list
>> address@hidden
>> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>> 
>
>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel



Never miss a thing. Make Yahoo your homepage.
reply via email to

[Prev in Thread] Current Thread [Next in Thread]