Hi guys,
I'm typing this mail from Ubuntu! So the internet is setup, envy did its job ( in manual mode though ). Paparazzi dev and arm7 packages were downloaded, and the cvs source code installed. I compiled it using make and then tried to see if paparazzi center started up, it did. So, generally, everything here seems to be working, BUT, the simulation does not run. When I say make demo, it raises an error towards the end saying Twin1 cant be found in conf.xml. I looked at the airframes folder, and there is no Twin1 there, and there is no Twin1 mentioned in the conf.xml file either. I tried to be smart and created a duplicate of one of the other airframe files and saved it as Twin1. It gives the following
error when I run make demo: ( only the last bit gives this error )
cd sw/airborne; make PAPARAZZI_SRC=/home/dcenterprises/paparazzi/paparazzi3 PAPARAZZI_HOME=/home/dcenterprises/paparazzi/paparazzi3 TARGET=sim ARCHI=sim all
CC /home/dcenterprises/paparazzi/paparazzi3/var/Twin1/sim/fw_h_ctl.o
fw_h_ctl.c: In function ‘h_ctl_init’:
fw_h_ctl.c:110: error: ‘H_CTL_COURSE_PGAIN’ undeclared (first use in this function)
fw_h_ctl.c:110: error: (Each undeclared identifier is reported only once
fw_h_ctl.c:110: error: for each function it appears in.)
fw_h_ctl.c:112: error: ‘H_CTL_ROLL_MAX_SETPOINT’ undeclared (first use in this function)
fw_h_ctl.c:126: error: ‘H_CTL_PITCH_PGAIN’ undeclared (first use in this function)
fw_h_ctl.c:127: error: ‘H_CTL_PITCH_DGAIN’ undeclared (first use in this function)
fw_h_ctl.c:129: error: ‘H_CTL_ELEVATOR_OF_ROLL’ undeclared (first use in this function)
make[2]: ***
[/home/dcenterprises/paparazzi/paparazzi3/var/Twin1/sim/fw_h_ctl.o] Error 1
make[1]: *** [sim] Error 2
make: *** [ac1] Error 2
Anyone know whats happening? I understand the errors, but I don't know how to fix them here!
Thanks in advance,
Uttam
----- Original Message ----
From: David <address@hidden>
To: Uttam Chandrashekhar <address@hidden>
Sent: Wednesday, December 5, 2007 5:10:26 AM
Subject: Re: Can you please share your Tiny1.3 Gerber File?
Did it work with 64bit (network)?
"no internet" doesn't really mean bad drivers. Do you get green lights on the card itself (i.e. physical connection is valid)? What does: ifconfig command return?
I have yet to have Ubuntu not install network properly. I have many times had issues trying to setup wireless correctly, never driver level, just getting WEP/WPA other encrypted stuff working right.
Quite possibly this is simply settings not drivers.
-DC
On Dec 4, 2007, at 3:37 PM, Uttam Chandrashekhar wrote:
Dave,
Envy sounds good. I installed the 32 bit already, and I think something is wrong with the Network interface card drivers. I simply have no internet! I spent all of yesterday trying to sort the problem, no luck :(
-Uttam
----- Original Message ----
From: David Conger <
address@hidden>
To: Uttam
Chandrashekhar <
address@hidden>
Sent: Wednesday, December 5, 2007 3:46:26 AM
Subject: Re: Can you please share your Tiny1.3 Gerber File?
Uttam,
I saw this: "Hi,
Thanks. I tried the 64bit architecture and it did not recognize my NIC, or the graphic drivers. When I look at the installed devices, I see a lot of "unknowns". I am downloading the x86 version now, hopefully I can get the internet and graphics working in the x86 version.
-Thanks,
Uttam"
You should be okay with 64bit. You just have to install the 32bit compilers and libraries so you can compile it in 32 bit.
I say this because on my Desktop (AMD64) I installed 64bit Ubuntu but wanted to install sound drivers that were only 32 bit. I googled and found
directions to install/compile the 32 bit and it worked fine. I imagine the same would be the case for the paparazzi.
Did you try "envy" it's amazing, really, just trust me if you have nVidia graphics even if Ubuntu recognizes it...you want to run Envy...trust me. It downloads the right sources based on your system then recompiles them and even sets up the X config files. I now will only use nVidia cards because I know I have Envy to do the proper setup/config.
-David Conger
On Dec 2, 2007 11:46 PM, Uttam Chandrashekhar <
address@hidden> wrote:
Hi Dave,
Sure, here you go, Gerbers attached. Our PCB's are getting made! Please let me know if there's anything else.
-Thanks,
Best Regards,
Uttam
----- Original Message ----
From: David Conger <
address@hidden>
To:
address@hiddenSent: Monday, December 3, 2007 11:48:56 AM
Subject: Can you please share your Tiny1.3 Gerber File?
Hi Uttam,
I have been following the Paparazzi list for some time. I want to create Gerber files but am having issues.
I was trying to follow your directions but you don't list specifically what layers to add or what layers to check in the layer list when editing the gerber job...
Can you please email me your gerber file you were sent? I need to have some FAB myself and worry I will send an inappropriate file.
Best Regards,
David
Conger
Be a better sports nut! Let your teams follow you with Yahoo Mobile.
Try it now.
Looking for last minute shopping deals? Find them fast with Yahoo! Search.