[Top][All Lists]

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Linphone-developers] problems in streaming on WAN for linphone por

From: Abhishek Ranjan
Subject: Re: [Linphone-developers] problems in streaming on WAN for linphone ported on TI DM365
Date: Thu, 10 Jun 2010 13:27:02 +0530

Hi Simon,

After some more debugging and wireshark logs on both caller and receiver side ,we found out the following:

--we make the all using proxy
-- The reciever starts sending the packet as soon as it accepts  the call and it sends all the packet starting from RTP seq 0(from the wireshark logs on receiver side)
--  The caller on receiving 200 OK sends the acknowledgement and starts sending the packets.
-- But it receives the packet starting from RTP seq no 40-100. So it does not receive all the packtes which the receiver has sent. it does not receive packets from 0-40. which is causing our decoder somehow to fail as it does not receive the Visual Object Sequence header
-- Looks like this is a problem of pin hole opening I mean until a packet is sent out from a RTP port, it can't receive any packet from outside
-- As the caller starts sending the packets late after receiving the 200 Ok, till that time RTP port on called side is not open so it misses some initial packets sent by receiver.
-- I tried to confirm this by putting some sleep after sending 200 Ok from receiver side, that is delay the sending of packets from receiver side.. so in this case receiver side pinhole is not opened so it misses some initial packet from caller side.. while caller recieves all the RTP packtes from the beginning. So in this case video comes on the caller side..

How to make sure the ports are opened before any RTP packet is received,..Would stun server help??


On Wed, Jun 9, 2010 at 6:06 PM, Simon Morlat <address@hidden> wrote:

Maybe RTP packets are too big then discarded while going through the
internet ?


Le jeudi 03 juin 2010 à 21:51 +0530, Abhishek Ranjan a écrit :
> HI all,
> We are using linphone source for our SIP phone development on TI DM365
> SOC. I have written filters for video encoding and decoding which uses
> TI's hardware encoder and decoder chip for video enc/dec operation and
> the rtp stack I am using as is. The audio part is same as present in
> linphone wiht G711 codec.
> For video My graph is very simple:
> cap_enc filter------> rtpsend
> rtprecv----------------->decode_display filter
> where cap_enc and decode_display filters are developed by us.
> We have successfully tested the sytem in LAN (Local Area
> Network)conditions where there is no limit on upload/download
> speed.and we have absolutely no problems in LAN testing conditions.
> But we are facing issues while making calls on WAN via proxy. We are
> getting video in only one direction. But nothing in other direction.
> The issue we are facing is linphone is not able to send RTP packets on
> other side.
> -- Our test set up consist of one unit connected to 1 Mbps broadband
> and the other one to a 2 Mbps leased line connection.
> -- The video resolution we are using is 4-CIF
> -- tried to experiment with jitt_compensation but nothing happened
> other than increase in delay
> -- Also tried to increase the video compression by relaxing the
> quantization parameter..
> -- The video decode and display is successful on the unit which
> receives the call and this is consistent all the time. We dont get any
> successful decoding and display on the unit making the call.
> -- RTP statistics showing that no of rtp packtes successfully
> delivered to the application is very low compared to the total number
> of packets received.
> Any suggestion on what could possibly go wrong while switching from
> LAN to WAN.
> Thanks,
> Abhishek Ranjan
> _______________________________________________
> Linphone-developers mailing list
> address@hidden

reply via email to

[Prev in Thread] Current Thread [Next in Thread]