|
From: | محمد روسلي |
Subject: | Re: [Discuss-gnuradio] Question about benchmark_tx and benchmark_rx |
Date: | Thu, 15 Dec 2011 11:06:01 +1300 |
Hi,
I am using:
OS: Ubuntu 11.10 (which I read in blog said that it has some problem with gnuradio)
Gnuradio: 3.5.0 rc 0 (which I git from master branch)
I quite puzzled it's not working with my current setup. It seems doable by many people but not me.
Regards,
Muhammad b Rosli
Student
Bachelor of Electrical and Electronic
University of CanterburyOn Wed, Dec 7, 2011 at 12:14 PM, Tom Rondeau <address@hidden> wrote:
On Thu, Dec 1, 2011 at 10:15 PM, Muhammad Rosli <address@hidden> wrote:
Hi,
Thanks for your reply. I am using the narrowband example.
If I attempt using
./benchmark_tx.py -f 400M -r 250k -S 4
and
./benchmark_rx.py -f 400M -r 250k -S 4
which I worked out from reading the README file, the receiver still output overrun (many '0'). I verified that the transmitter working since my spectrum analyser can pickup the signal from the transmitter.
--
Regards,
Muhammad b Rosli
Student
Bachelor of Electrical and Electronic
University of CanterburyWhat is your OS, version of GNU Radio, hardware?By default, the digital benchmarks run GMSK, so that with 250 kbps rate should be easily doable without overruns on most modern machines.TomOn Fri, Dec 2, 2011 at 3:56 PM, Marcus D. Leech <address@hidden> wrote:
_______________________________________________You're asking for 10 samples per symbol, which may exceed the rate at which your receiver computer can keep up, depending onOn 12/01/2011 09:36 PM, Muhammad Rosli wrote:Hi,
Thanks for reading my mail. I would like to ask is there any additional setup or configuration required to execute benchmark_tx.py and benchmark_rx.py?
My problem is I tried to initiate simple communication between two USRP1 using benchmark_rx.py and benchmark_tx.py . I had browse through the mailing list looking on how to use the file appropriately. Running benchmark_tx.py also execute help which I follow closely but failed to receive any packets. If I tried to execute at transmitter:
benchmark_tx.py -f 400M -S 10
and at receiver
benchmark_rx.py -f 400M -S 10
I did not received packet status. I only received '0' in the terminal. Is it correspond to error?
I also read mailing list sent by other members but none mentioned about not able to execute benchmark_tx.py . If I missed any post, could anyone please provide me the link.
For additional information:
Gnuradio version used: v3.5.0rc0
USRP1 : revision 4
Ubuntu: 11.10
Daugtherboard: SBX
Please let me know if I had to provide any additional information.
--
Regards,
Muhammad b Rosli
Student
Bachelor of Electrical and Electronic
University of Canterbury
the modulation used, and the complexity of the modulation techniques. Are you using the narrowband or ofdm examples?
The 'O' means overrun. The hardware (USRP1) is sending samples faster than your computer can keep up.
-- Marcus Leech Principal Investigator Shirleys Bay Radio Astronomy Consortium http://www.sbrac.org
Discuss-gnuradio mailing list
address@hidden
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
_______________________________________________
Discuss-gnuradio mailing list
address@hidden
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
--
Regards,
Muhammad b Rosli
Student
Bachelor of Electrical and Electronic
University of Canterbury
[Prev in Thread] | Current Thread | [Next in Thread] |