[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Tlf-devel] Using TLF with hamlib
From: |
Bob Nielsen |
Subject: |
Re: [Tlf-devel] Using TLF with hamlib |
Date: |
Thu, 05 May 2005 19:58:59 -0700 |
I tried the TS-570D with xlog and hamlib and had similar problems.
Strangely, grig works for the most part (it talks to the radio but a few
functions don't respond). I'll see if I can figure out what is
happening or ask on the hamlib list. I'll also finish the I/O card for
my K2 and give that a try.
Bob, N7XY
On Wed, 2005-05-04 at 12:13 +0200, Rein Couperus PA0R wrote:
> I have tlf-0.9.23 running without problem with hamblib 1.2.4 and the
> ORION (rig nr. 1608). Also no problem with the K2.
>
> my config.h says:
>
> /* Define if you have the <hamlib/riglist.h> header file. */
> /* #undef HAVE_HAMLIB_RIGLIST_H */
>
> /* Define if you have the <hamlib/rig.h> header file. */
> #define HAVE_HAMLIB_RIG_H 1
>
> /* Define if you have the <inttypes.h> header file. */
> #define HAVE_INTTYPES_H 1
>
> /* Define if you have the `hamlib' library (-lhamlib). */
> #define HAVE_LIBHAMLIB 1
>
> Looks like tlf does not need riglist.h
>
> Moreover, the error message you get is not from tlf, but from hamlib, so
> I would look in that direction...
>
> Anybody else have problems with the TS570D ?
>
> Rein PA0R
>
>
>
>
>
> On Mon, 2005-05-02 at 16:55 -0700, Bob Nielsen wrote:
> > I finally got around to trying to interface my TS-570D to my computer.
> > It works fine with grig, but I haven't been able to get the rig to talk
> > to TLF.
> >
> > I ran configure with --enable-hamlib. It appears to recognize hamlib:
> >
> > checking for main in -lhamlib... yes
> > checking hamlib/rig.h usability... yes
> > checking hamlib/rig.h presence... yes
> > checking for hamlib/rig.h... yes
> > enabling hamlib support
> >
> > However, checking the resultant config.h, I see:
> >
> >
> > /* Define if you have the <hamlib/riglist.h> header file. */
> > /* #undef HAVE_HAMLIB_RIGLIST_H */
> >
> > However, /usr/include/hamlib/riglist.h exists.
> >
> > I compiled TLF and enabled rig control in logcfg.dat, setting RIGMODEL,
> > RIGSPEED and RIGPORT to the appropriate values. When I run TLF, I get
> > the following:
> >
> > Trying to start rig ctrl
> > rig_open: error
> >
> > Editing config.h to define HAVE_HAMLIB_RIGLIST_H doesn't help
> >
> > TLF is version 0.9.23 and hamlib-dev is version 1.2.4-1. The system is
> > a 1.2 GHz Celeron running Libranet 2.8.1 updated with packages from
> > Debian Sarge and Sid.
> >
> > Any ideas?
> >
> > TIA and 73,
> >
> > Bob, N7XY
> >
>
>
>