qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [Bug 1753309] Re: Ethernet interrupt vectors for sabrelite


From: Thomas Huth
Subject: [Qemu-devel] [Bug 1753309] Re: Ethernet interrupt vectors for sabrelite machine are defined backwards
Date: Thu, 26 Apr 2018 05:03:38 -0000

** Changed in: qemu
       Status: Fix Committed => Fix Released

-- 
You received this bug notification because you are a member of qemu-
devel-ml, which is subscribed to QEMU.
https://bugs.launchpad.net/bugs/1753309

Title:
  Ethernet interrupt vectors for sabrelite machine are defined backwards

Status in QEMU:
  Fix Released

Bug description:
  The sabrelite machine model used by qemu-system-arm is based on the
  Freescale/NXP i.MX6Q processor. This SoC has an on-board ethernet
  controller which is supported in QEMU using the imx_fec.c module
  (actually called imx.enet for this model.)

  The include/hw/arm/fsm-imx6.h file defines the interrupt vectors for
  the imx.enet device like this:

  #define FSL_IMX6_ENET_MAC_1588_IRQ 118
  #define FSL_IMX6_ENET_MAC_IRQ 119

  However, this is backwards. The reference manual for the i.MX6D/Q
  devices can be found here:

  https://www.nxp.com/docs/en/reference-manual/IMX6DQRM.pdf

  On page 225, in Table 3-1. ARM Cortex A9 domain interrupt summary, it
  shows the following:

  150 ENET
  MAC 0 IRQ, Logical OR of:
  MAC 0 Periodic Timer Overflow
  MAC 0 Time Stamp Available
  MAC 0 Time Stamp Available
  MAC 0 Time Stamp Available
  MAC 0 Payload Receive Error
  MAC 0 Transmit FIFO Underrun
  MAC 0 Collision Retry Limit
  MAC 0 Late Collision
  MAC 0 Ethernet Bus Error
  MAC 0 MII Data Transfer Done
  MAC 0 Receive Buffer Done
  MAC 0 Receive Frame Done
  MAC 0 Transmit Buffer Done
  MAC 0 Transmit Frame Done
  MAC 0 Graceful Stop
  MAC 0 Babbling Transmit Error
  MAC 0 Babbling Receive Error
  MAC 0 Wakeup Request [synchronous]

  151 ENET
  MAC 0 1588 Timer interrupt [synchronous] request

  Note:
  150 - 32 == 118
  151 - 32 == 119

  In other words, the vector definitions in the fsl-imx6.h file are
  reversed. The correct definition is:

  #define FSL_IMX6_ENET_MAC_IRQ 118
  #define FSL_IMX6_ENET_MAC_1588_IRQ 119

  I tested the sabrelite simulation using VxWorks 7 (which supports the
  SabreLite board) and found that while I was able to send and receive
  packet data via the simulated ethernet interface, the VxWorks i.MX6
  ethernet driver failed to receive any interrupts. When I corrected the
  interrupt vector definitions as shown above and recompiled QEMU,
  everything worked as expected. I was able to exchange ICMP packets
  with the simulated target and telnet to/from the VxWorks instance
  running in the virtual machine. I used the tap interface for this.

  As a workaround I was also able to make the ethernet work by modifying
  the VxWorks imx6q-sabrelite.dts file to change the ethernet interrupt
  property from 150 to 151.

  This problem was observed with the following environment:

  Host: FreeBSD/amd64 11.1-RELEASE
  QEMU version: 2.11.0 and 2.11.1 built from source code

To manage notifications about this bug go to:
https://bugs.launchpad.net/qemu/+bug/1753309/+subscriptions



reply via email to

[Prev in Thread] Current Thread [Next in Thread]