Re: [Qemu-devel] [PATCH v2 1/2] xilinx_spips: Enable only two slaves when reading/writing with stripe

[francisco iglesias]

On Tuesday, 27 February 2018, Alistair Francis <address@hidden> wrote:

> On Fri, Feb 23, 2018 at 3:22 PM, Francisco Iglesias
> <address@hidden> wrote:
> > Assert only the lower cs on bus 0 and upper cs on bus 1 when both buses
> and
> > chip selects are enabled (e.g reading/writing with stripe).
> >
> > Signed-off-by: Francisco Iglesias <address@hidden>
>
> Reviewed-by: Alistair Francis <address@hidden>
> Tested-by: Alistair Francis <address@hidden>
>
> Alistair
>
> > ---
> >  hw/ssi/xilinx_spips.c | 41 +++++++++++++++++++++++++++++++++++++----
> >  1 file changed, 37 insertions(+), 4 deletions(-)
> >
> > diff --git a/hw/ssi/xilinx_spips.c b/hw/ssi/xilinx_spips.c
> > index 8af36ca3d4..0cb484ecf4 100644
> > --- a/hw/ssi/xilinx_spips.c
> > +++ b/hw/ssi/xilinx_spips.c
> > @@ -223,7 +223,7 @@ static void xilinx_spips_update_cs(XilinxSPIPS *s,
> int field)
> >  {
> >      int i;
> >
> > -    for (i = 0; i < s->num_cs; i++) {
> > +    for (i = 0; i < s->num_cs * s->num_busses; i++) {
> >          bool old_state = s->cs_lines_state[i];
> >          bool new_state = field & (1 << i);
> >
> > @@ -234,7 +234,7 @@ static void xilinx_spips_update_cs(XilinxSPIPS *s,
> int field)
> >          }
> >          qemu_set_irq(s->cs_lines[i], !new_state);
> >      }
> > -    if (!(field & ((1 << s->num_cs) - 1))) {
> > +    if (!(field & ((1 << (s->num_cs * s->num_busses)) - 1))) {
> >          s->snoop_state = SNOOP_CHECKING;
> >          s->cmd_dummies = 0;
> >          s->link_state = 1;
> > @@ -248,7 +248,40 @@ static void 
> > xlnx_zynqmp_qspips_update_cs_lines(XlnxZynqMPQSPIPS
> *s)
> >  {
> >      if (s->regs[R_GQSPI_GF_SNAPSHOT]) {
> >          int field = ARRAY_FIELD_EX32(s->regs, GQSPI_GF_SNAPSHOT,
> CHIP_SELECT);
> > -        xilinx_spips_update_cs(XILINX_SPIPS(s), field);
> > +        bool upper_cs_sel = field & (1 << 1);
> > +        bool lower_cs_sel = field & 1;
> > +        bool bus0_enabled;
> > +        bool bus1_enabled;
> > +        uint8_t buses;
> > +        int cs = 0;
> > +
> > +        buses = ARRAY_FIELD_EX32(s->regs, GQSPI_GF_SNAPSHOT,
> DATA_BUS_SELECT);
> > +        bus0_enabled = buses & 1;
> > +        bus1_enabled = buses & (1 << 1);
> > +
> > +        if (bus0_enabled && bus1_enabled) {
> > +            if (lower_cs_sel) {
> > +                cs |= 1;
> > +            }
> > +            if (upper_cs_sel) {
> > +                cs |= 1 << 3;
> > +            }
> > +        } else if (bus0_enabled) {
> > +            if (lower_cs_sel) {
> > +                cs |= 1;
> > +            }
> > +            if (upper_cs_sel) {
> > +                cs |= 1 << 1;
> > +            }
> > +        } else if (bus1_enabled) {
> > +            if (lower_cs_sel) {
> > +                cs |= 1 << 2;
> > +            }
> > +            if (upper_cs_sel) {
> > +                cs |= 1 << 3;
> > +            }
> > +        }
> > +        xilinx_spips_update_cs(XILINX_SPIPS(s), cs);
> >      }
> >  }
> >
> > @@ -260,7 +293,7 @@ static void xilinx_spips_update_cs_lines(XilinxSPIPS
> *s)
> >      if (num_effective_busses(s) == 2) {
> >          /* Single bit chip-select for qspi */
> >          field &= 0x1;
> > -        field |= field << 1;
> > +        field |= field << 3;
> >      /* Dual stack U-Page */
> >      } else if (s->regs[R_LQSPI_CFG] & LQSPI_CFG_TWO_MEM &&
> >                 s->regs[R_LQSPI_STS] & LQSPI_CFG_U_PAGE) {
> > --
> > 2.11.0
> >
> >
>

Hi Alistair,

Thank you very much once again for reviewing and testing!

Best regards,
Francisco Iglesias