[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Qemu-devel] QEMU terminates during reboot after memory unplug with
From: |
Bharata B Rao |
Subject: |
Re: [Qemu-devel] QEMU terminates during reboot after memory unplug with vhost=on |
Date: |
Thu, 14 Sep 2017 15:50:37 +0530 |
User-agent: |
Mutt/1.7.1 (2016-10-04) |
On Thu, Sep 14, 2017 at 10:59:05AM +0200, Igor Mammedov wrote:
> On Thu, 14 Sep 2017 13:48:26 +0530
> Bharata B Rao <address@hidden> wrote:
>
> > On Thu, Sep 14, 2017 at 10:00:11AM +0200, Igor Mammedov wrote:
> > > On Thu, 14 Sep 2017 12:31:18 +0530
> > > Bharata B Rao <address@hidden> wrote:
> > >
> > > > Hi,
> > > >
> > > > QEMU hits the below assert
> > > >
> > > > qemu-system-ppc64: used ring relocated for ring 2
> > > > qemu-system-ppc64: qemu/hw/virtio/vhost.c:649: vhost_commit: Assertion
> > > > `r >= 0' failed.
> > > >
> > > > in the following scenario:
> > > >
> > > > 1. Boot guest with vhost=on
> > > > -netdev
> > > > tap,id=mynet0,script=qemu-ifup,downscript=qemu-ifdown,vhost=on -device
> > > > virtio-net-pci,netdev=mynet0
> > > > 2. Hot add a DIMM device
> > > > 3. Reboot
> > > > When the guest reboots, we can see
> > > > vhost_virtqueue_start:vq->used_phys getting assigned an address that
> > > > falls in the hotplugged memory range.
> > > > 4. Remove the DIMM device
> > > > Guest refuses the removal as the hotplugged memory is under use.
> > > > 5. Reboot
> > >
> > > > QEMU forces the removal of the DIMM device during reset and that's
> > > > when we hit the above assert.
> > > I don't recall implementing forced removal om DIMM,
> > > could you point out to the related code, pls?
> >
> > This is ppc specific. We have DR Connector objects for each LMB (multiple
> > LMBs make up one DIMM device) and during reset we invoke the
> > release routine for these LMBs which will further invoke
> > pc_dimm_memory_unplug().
> >
> > See hw/ppc/spapr_drc.c: spapr_drc_reset()
> > hw/ppc/spapr.c: spapr_lmb_release()
> >
> > >
> > > > Any pointers on why we are hitting this assert ? Shouldn't vhost be
> > > > done with using the hotplugged memory when we hit reset ?
> > >
> > > >From another point of view,
> > > DIMM shouldn't be removed unless guest explicitly ejects it
> > > (at least that should be so in x86 case).
> >
> > While that is true for ppc also, shouldn't we start fresh from reset ?
> we should.
>
> when it aborts vhost should print out error from vhost_verify_ring_mappings()
>
> if (r == -ENOMEM) {
> error_report("Unable to map %s for ring %d", part_name[j], i);
>
> } else if (r == -EBUSY) {
>
> error_report("%s relocated for ring %d", part_name[j], i);
>
> that might give a clue where that memory stuck in.
As I mentioned above, it fails here:
> > > qemu-system-ppc64: used ring relocated for ring 2
Regards,
Bharata.