|
From: | Peter Crosthwaite |
Subject: | Re: [Qemu-devel] [PATCH for-2.5 v1 4/4] arm: xilinx_zynq: Add linux pre-boot |
Date: | Tue, 27 Oct 2015 08:21:37 -0700 |
On 25 October 2015 at 23:13, Peter Crosthwaite
<address@hidden> wrote:
> Add a Linux-specific pre-boot routine that matches the device
> specific bootloaders behaviour. This is needed for modern Linux that
> expects the ARM PLL in SLCR to be a more even value (not 26).
>
> Cc: Alistair Francis <address@hidden>
> Signed-off-by: Peter Crosthwaite <address@hidden>
> ---
> Changed since RFC:
> Use bootloader callback to load blob.
> Change "firmware" to "board-setup" for consistency.
>
> hw/arm/xilinx_zynq.c | 40 +++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 39 insertions(+), 1 deletion(-)
>
> diff --git a/hw/arm/xilinx_zynq.c b/hw/arm/xilinx_zynq.c
> index 9f89483..8c249e8 100644
> --- a/hw/arm/xilinx_zynq.c
> +++ b/hw/arm/xilinx_zynq.c
> @@ -43,6 +43,41 @@ static const int dma_irqs[8] = {
> 46, 47, 48, 49, 72, 73, 74, 75
> };
>
> +#define BOARD_SETUP_ADDR 0x0
> +#define LOAD_ADDR 0x1000
> +
> +#define SLCR_LOCK_OFFSET 0x004
> +#define SLCR_UNLOCK_OFFSET 0x008
> +#define SLCR_ARM_PLL_OFFSET 0x100
> +
> +#define SLCR_XILINX_UNLOCK_KEY 0xdf0d
> +#define SLCR_XILINX_LOCK_KEY 0x767b
> +
This could use a comment about what these insns are...
Not ending the macro with a trailing comma would make the
uses of it below look a bit more natural (since they then
have the comma sort of how you'd expect).
Otherwise> +
> +static void zynq_write_board_setup(ARMCPU *cpu,
> + const struct arm_boot_info *info)
> +{
> + int n;
> + uint32_t board_setup_blob[] = {
> + 0xe3a004f8, /* mov r0, #0xf8000000 */
> + SLCR_WRITE(SLCR_UNLOCK_OFFSET, SLCR_XILINX_UNLOCK_KEY)
> + SLCR_WRITE(SLCR_ARM_PLL_OFFSET, 0x00014008)
> + SLCR_WRITE(SLCR_LOCK_OFFSET, SLCR_XILINX_LOCK_KEY)
> + 0xe12fff1e, /* bx lr */
> + };
> + for (n = 0; n < ARRAY_SIZE(board_setup_blob); n++) {
> + board_setup_blob[n] = tswap32(board_setup_blob[n]);
> + }
> + rom_add_blob_fixed("board-setup", board_setup_blob,
> + sizeof(board_setup_blob), BOARD_SETUP_ADDR);
> +}
> +
> static struct arm_boot_info zynq_binfo = {};
>
> static void gem_init(NICInfo *nd, uint32_t base, qemu_irq irq)
> @@ -251,7 +286,10 @@ static void zynq_init(MachineState *machine)
> zynq_binfo.initrd_filename = initrd_filename;
> zynq_binfo.nb_cpus = 1;
> zynq_binfo.board_id = 0xd32;
> - zynq_binfo.loader_start = 0;
> + zynq_binfo.loader_start = LOAD_ADDR;
> + zynq_binfo.board_setup_addr = BOARD_SETUP_ADDR;
> + zynq_binfo.write_board_setup = zynq_write_board_setup;
> +
> arm_load_kernel(ARM_CPU(first_cpu), &zynq_binfo);
> }
>
> --
> 1.9.1
Reviewed-by: Peter Maydell <address@hidden>
thanks
-- PMM
[Prev in Thread] | Current Thread | [Next in Thread] |