Re: [Qemu-devel] [PATCH v2 1/1] ide/atapi: Mark non-data commands as complete

[Paolo Bonzini]

Il 13/09/2014 05:51, John Snow ha scritto:
> When the command completion code in IDE and AHCI
> was unified to put all command completion inside
> of a callback, "cmd_done," we neglected to
> ensure that all AHCI/ATAPI command paths would
> eventually register as finished. for the PCI
> interface to IDE this is not a problem because
> cmd_done is a nop, but the AHCI implementation
> needs to send a D2H_REG_FIS and interrupt back
> to the guest to inform of completion.
> 
> This patch adds calls to ide_stop_transfer,
> which calls ide_cmd_done, inside of
> ide_atapi_cmd_ok and ide_atapi_cmd_error.
> 
> This fixes regressions observed by trying to boot QEMU
> with a Fedora 20 live CD under Q35/AHCI, which uses
> ATAPI command 0x00, which is a status check that may
> cause a hang because we never complete, and ATAPI
> command 0x56, which is unsupported by our current
> implementation and results in an error that we never
> report back to the guest.
> 
> Signed-off-by: John Snow <address@hidden>
> ---
>  hw/ide/atapi.c | 7 +++----
>  1 file changed, 3 insertions(+), 4 deletions(-)
> 
> diff --git a/hw/ide/atapi.c b/hw/ide/atapi.c
> index 3d92b52..ee80c22 100644
> --- a/hw/ide/atapi.c
> +++ b/hw/ide/atapi.c
> @@ -134,6 +134,7 @@ void ide_atapi_cmd_ok(IDEState *s)
>      s->error = 0;
>      s->status = READY_STAT | SEEK_STAT;
>      s->nsector = (s->nsector & ~7) | ATAPI_INT_REASON_IO | 
> ATAPI_INT_REASON_CD;
> +    ide_transfer_stop(s);
>      ide_set_irq(s->bus);
>  }
>  
> @@ -147,6 +148,7 @@ void ide_atapi_cmd_error(IDEState *s, int sense_key, int 
> asc)
>      s->nsector = (s->nsector & ~7) | ATAPI_INT_REASON_IO | 
> ATAPI_INT_REASON_CD;
>      s->sense_key = sense_key;
>      s->asc = asc;
> +    ide_transfer_stop(s);
>      ide_set_irq(s->bus);
>  }
>  
> @@ -174,9 +176,7 @@ void ide_atapi_cmd_reply_end(IDEState *s)
>  #endif
>      if (s->packet_transfer_size <= 0) {
>          /* end of transfer */
> -        s->status = READY_STAT | SEEK_STAT;
> -        s->nsector = (s->nsector & ~7) | ATAPI_INT_REASON_IO | 
> ATAPI_INT_REASON_CD;
> -        ide_transfer_stop(s);
> +        ide_atapi_cmd_ok(s);
>          ide_set_irq(s->bus);
>  #ifdef DEBUG_IDE_ATAPI
>          printf("status=0x%x\n", s->status);
> @@ -186,7 +186,6 @@ void ide_atapi_cmd_reply_end(IDEState *s)
>          if (s->lba != -1 && s->io_buffer_index >= s->cd_sector_size) {
>              ret = cd_read_sector(s, s->lba, s->io_buffer, s->cd_sector_size);
>              if (ret < 0) {
> -                ide_transfer_stop(s);
>                  ide_atapi_io_error(s, ret);
>                  return;
>              }
> 

Reviewed-by: Paolo Bonzini <address@hidden>