Re: [Qemu-devel] [RESEND PATCH v5 4/4] vfio: Enable vfio-pci and mark supported

[Alex Williamson]

On Wed, 2012-09-26 at 08:50 -0500, Anthony Liguori wrote:
> Alex Williamson <address@hidden> writes:
> 
> > Enabled for all softmmu guests supporting PCI on Linux hosts.  Note
> > that currently only x86 hosts have the kernel side VFIO IOMMU support
> > for this.  PPC (g3beige) is the only non-x86 guest known to work.
> > ARM (veratile) hangs in firmware, others untested.
> >
> > Signed-off-by: Alex Williamson <address@hidden>
> > Acked-by: Michael S. Tsirkin <address@hidden>
> > ---
> >
> >  MAINTAINERS      |    5 +++++
> >  configure        |    6 ++++++
> >  hw/Makefile.objs |    3 ++-
> >  3 files changed, 13 insertions(+), 1 deletion(-)
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 25733fc..29aac4f 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -474,6 +474,11 @@ M: Gerd Hoffmann <address@hidden>
> >  S: Maintained
> >  F: hw/usb*
> >  
> > +VFIO
> > +M: Alex Williamson <address@hidden>
> > +S: Supported
> > +F: hw/vfio*
> > +
> >  vhost
> >  M: Michael S. Tsirkin <address@hidden>
> >  S: Supported
> > diff --git a/configure b/configure
> > index 1b86517..c2c0d4f 100755
> > --- a/configure
> > +++ b/configure
> > @@ -165,6 +165,7 @@ attr=""
> >  libattr=""
> >  xfs=""
> >  
> > +vfio_pci="no"
> >  vhost_net="no"
> >  kvm="no"
> >  gprof="no"
> > @@ -509,6 +510,7 @@ Haiku)
> >    usb="linux"
> >    kvm="yes"
> >    vhost_net="yes"
> > +  vfio_pci="yes"
> >    if [ "$cpu" = "i386" -o "$cpu" = "x86_64" ] ; then
> >      audio_possible_drivers="$audio_possible_drivers fmod"
> >    fi
> > @@ -3174,6 +3176,7 @@ echo "libiscsi support  $libiscsi"
> >  echo "build guest agent $guest_agent"
> >  echo "seccomp support   $seccomp"
> >  echo "coroutine backend $coroutine_backend"
> > +echo "VFIO PCI support  $vfio_pci"
> >  
> >  if test "$sdl_too_old" = "yes"; then
> >  echo "-> Your SDL version is too old - please upgrade to have SDL support"
> > @@ -3911,6 +3914,9 @@ if test "$target_softmmu" = "yes" ; then
> >    if test "$smartcard_nss" = "yes" ; then
> >      echo "subdir-$target: subdir-libcacard" >> $config_host_mak
> >    fi
> > +  if test "$vfio_pci" = "yes" ; then
> > +    echo "CONFIG_VFIO_PCI=y" >> $config_target_mak
> > +  fi
> >    case "$target_arch2" in
> >      i386|x86_64)
> >        echo "CONFIG_HAVE_CORE_DUMP=y" >> $config_target_mak
> > diff --git a/hw/Makefile.objs b/hw/Makefile.objs
> > index 6dfebd2..7f8d3e4 100644
> > --- a/hw/Makefile.objs
> > +++ b/hw/Makefile.objs
> > @@ -198,7 +198,8 @@ obj-$(CONFIG_VGA) += vga.o
> >  obj-$(CONFIG_SOFTMMU) += device-hotplug.o
> >  obj-$(CONFIG_XEN) += xen_domainbuild.o xen_machine_pv.o
> >  
> > -# Inter-VM PCI shared memory
> > +# Inter-VM PCI shared memory & VFIO PCI device assignment
> >  ifeq ($(CONFIG_PCI), y)
> >  obj-$(CONFIG_KVM) += ivshmem.o
> > +obj-$(CONFIG_VFIO_PCI) += vfio_pci.o
> 
> Why not just make this
> 
> obj-$(CONFIG_LINUX) += vfio_pci.o
> 
> ?
> 
> All you're doing in configure is setting CONFIG_VFIO_PCI if
> CONFIG_LINUX.

Ok.  I thought I needed linux + softmmu + pci, but maybe the softmmu is
implied with CONFIG_PCI?  Thanks,

Alex