[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device m
From: |
Peter Crosthwaite |
Subject: |
Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model |
Date: |
Tue, 28 Feb 2012 11:04:34 +1000 |
On Tue, Feb 28, 2012 at 1:45 AM, Paul Brook <address@hidden> wrote:
>> On Tue, Feb 21, 2012 at 11:04 PM, Paul Brook <address@hidden> wrote:
>> >> > +static inline int64_t is_between(int64_t x, int64_t a, int64_t b)
>> >> > +{
>> >> > + if (a < b) {
>> >> > + return x > a && x <= b;
>> >> > + }
>> >> > + return x < a && x >= b;
>> >> > +}
>> >>
>> >> This looks slightly odd -- should the boundary condition for whether
>> >> a value equal to the max/min really change depending on :whether a
>> >> or b is greater?
>>
>> The function determines whether x is in-between a and b exclusive of
>> a, inclusive of b, so it is consistent with itself in that regard.
>>
>> > This is a ugly hack. Instead of figuring out whether we have a count-up
>> > or count-down timer the code checks for both, and have the "in_between"
>> > function magically DTRT. I haven't followed the paths through in enough
>> > detail to figure out whether it gets all the corner cases right.
>>
>> Is it really a "hack"?? For count up b will always be greater than a,
>> and for count down the reverse. I suppose I could assert these
>> conditions at the call site for peace of mind? The invocation from
>> cadence_timer_run doesn't care whether it is count up of count down,
>> it really does just only care if the match value is in-between the
>> current timer value and the next timer value, which is exactly what
>> this function determines.
>
> When you explain it like this, it makes a more sense. But this isn't
> immediately obvious from the code. It took me at least a couple of readings
> to figure out what was going on. This is exactly the sort of thing that should
> be described in comments.
Ok, ill be a little more descriptive :)
A function with a very generic name
Perhaps clarify the whole inclusive a exclusive b in comment?
is used in a
> way that has fairly subtle implications. There's a good chance someone[1]
> will come along in a few months/years, reuse this function and "fix" the
> wierdness at the same time.
>
> Annother non-obvious detail is the way you handle overflow. Specifically you
> check a range both plus and minus the wrap value before wrapping the final
> count. This is certainly confusing/surprising when you first encounter it.
> Very large steps result in overlapping ranges, which triggers [in this case
> harmless] warning bells.
>
> Thinking about that, I realised why I don't like the following line:
>
>> + s->reg_value = (uint32_t)((x + interval) % interval);
>
> This assumes x > -interval, which is not always true.
This would mean you have wrapped twice or more in one time step, which
I am assuming is a fatal error condition, as It means your software
has missed interrupts and all sort of race conditions would occur. I
would personally prefer to assert !(x < -interval) and have qemu
hw_error or something, as in these cases QEMU can just not handle your
super quick timer wrap around.
>
> Paul
>
> [1] "someone" includes me. After I've forgotten this obscure detail.
- [Qemu-devel] [PATCH v6 0/4] Zynq-7000 EPP platform model, Peter A. G. Crosthwaite, 2012/02/19
- [Qemu-devel] [PATCH v6 1/4] cadence_uart: initial version of device model, Peter A. G. Crosthwaite, 2012/02/19
- [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model, Peter A. G. Crosthwaite, 2012/02/19
- Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model, Peter Maydell, 2012/02/20
- Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model, Paul Brook, 2012/02/21
- Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model, Peter Crosthwaite, 2012/02/22
- Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model, Paul Brook, 2012/02/27
- Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model,
Peter Crosthwaite <=
- Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model, Peter Crosthwaite, 2012/02/27
- Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model, Paul Brook, 2012/02/28
- Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model, Peter Crosthwaite, 2012/02/28
- Re: [Qemu-devel] [PATCH v6 2/4] cadence_ttc: initial version of device model, Peter Crosthwaite, 2012/02/22
[Qemu-devel] [PATCH v6 3/4] cadence_gem: initial version of device model, Peter A. G. Crosthwaite, 2012/02/19
[Qemu-devel] [PATCH v6 4/4] xilinx_zynq: machine model initial version, Peter A. G. Crosthwaite, 2012/02/19
Re: [Qemu-devel] [PATCH v6 0/4] Zynq-7000 EPP platform model, Peter Crosthwaite, 2012/02/19
[Qemu-devel] [PULL] Zynq-7000 EPP platform model, Peter Crosthwaite, 2012/02/20