[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Qemu-arm] [PATCH v1 2/2] target-arm: Extend PAR format determinatio
From: |
Peter Maydell |
Subject: |
Re: [Qemu-arm] [PATCH v1 2/2] target-arm: Extend PAR format determination |
Date: |
Mon, 10 Jul 2017 16:11:29 +0100 |
On 30 June 2017 at 14:45, Edgar E. Iglesias <address@hidden> wrote:
> From: "Edgar E. Iglesias" <address@hidden>
>
> Extend PAR format determination to handle more cases.
>
> Signed-off-by: Edgar E. Iglesias <address@hidden>
> ---
> target/arm/helper.c | 30 +++++++++++++++++++++++++++++-
> 1 file changed, 29 insertions(+), 1 deletion(-)
>
> diff --git a/target/arm/helper.c b/target/arm/helper.c
> index fd1027e..6a1fffe 100644
> --- a/target/arm/helper.c
> +++ b/target/arm/helper.c
> @@ -2345,12 +2345,40 @@ static uint64_t do_ats_write(CPUARMState *env,
> uint64_t value,
> uint32_t fsr;
> bool ret;
> uint64_t par64;
> + bool format64 = false;
> MemTxAttrs attrs = {};
> ARMMMUFaultInfo fi = {};
>
> ret = get_phys_addr(env, value, access_type, mmu_idx,
> &phys_addr, &attrs, &prot, &page_size, &fsr, &fi);
> - if (extended_addresses_enabled(env)) {
> +
> + if (is_a64(env)) {
> + format64 = true;
> + } else if (arm_feature(env, ARM_FEATURE_LPAE)) {
> + /*
> + * ATS1Cxx:
> + * * TTBCR.EAE determines whether the result is returned using the
> + * 32-bit or the 64-bit PAR format
> + * * Instructions executed in Hyp mode always use the 64bit format
> + *
> + * ATS1S2NSOxx uses the 64bit format if any of the following is true:
> + * * The Non-secure TTBCR.EAE bit is set to 1
> + * * The implementation includes EL2, and the value of HCR.VM is 1
> + *
> + * ATS1Hx always uses the 64bit format (not supported yet).
> + */
> + format64 = regime_using_lpae_format(env, mmu_idx);
> +
> + if (arm_feature(env, ARM_FEATURE_EL2)) {
> + if (mmu_idx == ARMMMUIdx_S12NSE0 || mmu_idx ==
> ARMMMUIdx_S12NSE1) {
> + format64 |= env->cp15.hcr_el2 & HCR_VM;
> + } else {
> + format64 |= arm_current_el(env) == 2;
> + }
> + }
> + }
So this kind of worries me, because what it's coded as is "determine
whether architecturally we should be returning a 64-bit or 32-bit
PAR format", but what the code below it uses the format64 flag for is
"manipulate whatever PAR we got handed back by get_phys_addr()".
So we have two separate bits of code that are both choosing
32 vs 64 bit PAR (the code in this patch, and the logic inside
get_phys_addr()), and they have to come to the same conclusion
or we'll silently mangle the PAR. It seems like it would be
better to either have get_phys_addr() explicitly tell us what kind
of format it is returning to us, or to have the caller tell it
what kind of PAR it needs.
PS: on the subject of virtualization, I notice there's a comment
a bit later on in do_ats_write() that says
/* Note that S2WLK and FSTAGE are always zero, because we don't
* implement virtualization and therefore there can't be a stage 2
* fault.
*/
so we'll need to address that too at some point...
thanks
-- PMM
- Re: [Qemu-arm] [PATCH v1 2/2] target-arm: Extend PAR format determination,
Peter Maydell <=