paparazzi-commits
[Top][All Lists]
Advanced
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[paparazzi-commits] [6330] adding two airframes for lisa/L and lisa/M on

From: antoine drouin
Subject: [paparazzi-commits] [6330] adding two airframes for lisa/L and lisa/M on fixedwing
Date: Thu, 04 Nov 2010 15:39:15 +0000 
Revision: 6330
          http://svn.sv.gnu.org/viewvc/?view=rev&root=paparazzi&revision=6330
Author:   poine
Date:     2010-11-04 15:39:14 +0000 (Thu, 04 Nov 2010)
Log Message:
-----------
adding two airframes for lisa/L and lisa/M on fixedwing

Modified Paths:
--------------
    paparazzi3/trunk/conf/airframes/Poine/swift_1.xml

Added Paths:
-----------
    paparazzi3/trunk/conf/airframes/Poine/funjet42.xml

Added: paparazzi3/trunk/conf/airframes/Poine/funjet42.xml
===================================================================
--- paparazzi3/trunk/conf/airframes/Poine/funjet42.xml                          
(rev 0)
+++ paparazzi3/trunk/conf/airframes/Poine/funjet42.xml  2010-11-04 15:39:14 UTC 
(rev 6330)
@@ -0,0 +1,146 @@
+<!DOCTYPE airframe SYSTEM "../airframe.dtd">
+
+<!-- Funjet Multiplex (http://www.multiplex-rc.de/), Jeti ECO 25
+     Lisa/L board (http://paparazzi.enac.fr/wiki/Lisa)
+     XBee modem with AT firmware
+     LEA 5H GPS
+-->
+
+<airframe name="Delta Wing">
+
+  <firmware name="fixedwing">
+    <target name="sim"                         board="pc"/>
+    <target name="ap"                  board="lisa_l_1.0"/>
+
+    <subsystem name="radio_control"     type="ppm"/>
+    <subsystem name="telemetry"        type="transparent"/>
+    <subsystem name="control"/>
+    <subsystem name="attitude"                 type="infrared"/>
+    <subsystem name="gps"              type="ublox_lea5h"/>
+    <subsystem name="navigation"/>
+  </firmware>
+
+  <servos>
+    <servo name="MOTOR"         no="0" min="1000" neutral="1000" max="2000"/>
+    <servo name="AILEVON_LEFT"  no="1" min="1900" neutral="1521" max="1100"/>
+    <servo name="AILEVON_RIGHT" no="2" min="1100" neutral="1510" max="1900"/>
+  </servos>
+
+  <commands>
+    <axis name="THROTTLE" failsafe_value="0"/>
+    <axis name="ROLL"     failsafe_value="0"/>
+    <axis name="PITCH"    failsafe_value="0"/>
+  </commands>
+
+  <rc_commands>
+    <set command="THROTTLE" value="@THROTTLE"/>
+    <set command="ROLL"     value="@ROLL"/>
+    <set command="PITCH"    value="@PITCH"/>
+  </rc_commands>
+
+  <section name="MIXER">
+    <define name="AILEVON_AILERON_RATE" value="0.45"/>
+    <define name="AILEVON_ELEVATOR_RATE" value="0.8"/>
+  </section>
+
+  <command_laws>
+    <let var="aileron"  value="@ROLL  * AILEVON_AILERON_RATE"/>
+    <let var="elevator" value="@PITCH * AILEVON_ELEVATOR_RATE"/>
+    <set servo="MOTOR"           value="@THROTTLE"/>
+    <set servo="AILEVON_LEFT"  value="$elevator + $aileron"/>
+    <set servo="AILEVON_RIGHT" value="$elevator - $aileron"/>
+  </command_laws>
+
+  <section name="AUTO1" prefix="AUTO1_">
+    <define name="MAX_ROLL" value="RadOfDeg(50)"/>
+    <define name="MAX_PITCH" value="RadOfDeg(35)"/>
+  </section>
+
+  <section name="INFRARED" prefix="IR_">
+    <define name="ADC_IR1_NEUTRAL" value="512"/>
+    <define name="ADC_IR2_NEUTRAL" value="512"/>
+    <define name="ADC_TOP_NEUTRAL" value="512"/>
+
+    <define name="LATERAL_CORRECTION" value="-1"/>
+    <define name="LONGITUDINAL_CORRECTION" value="1"/>
+    <define name="VERTICAL_CORRECTION" value="1.5"/>
+
+    <define name="HORIZ_SENSOR_TILTED" value="1"/>
+    <define name="IR1_SIGN" value="1"/>
+    <define name="IR2_SIGN" value="-1"/>
+    <define name="TOP_SIGN" value="-1"/>
+
+    <define name="ROLL_NEUTRAL_DEFAULT" value="0" unit="deg"/>
+    <define name="PITCH_NEUTRAL_DEFAULT" value="0" unit="deg"/>
+  </section>
+
+  <section name="BAT">
+    <define name="CATASTROPHIC_BAT_LEVEL" value="9.3" unit="V"/>
+  </section>
+
+  <section name="MISC">
+    <define name="NOMINAL_AIRSPEED" value="15." unit="m/s"/>
+    <define name="CARROT" value="5." unit="s"/>
+    <define name="KILL_MODE_DISTANCE" value="(1.5*MAX_DIST_FROM_HOME)"/>
+    <define name="CONTROL_RATE" value="60" unit="Hz"/>
+
+    <define name="DEFAULT_CIRCLE_RADIUS" value="120."/>
+  </section>
+
+  <section name="VERTICAL CONTROL" prefix="V_CTL_">
+    <define name="POWER_CTL_BAT_NOMINAL" value="11.1" unit="volt"/>
+    <!-- outer loop proportional gain -->
+    <define name="ALTITUDE_PGAIN" value="-0.06"/> <!-- -0.024 -->
+    <!-- outer loop saturation -->
+    <define name="ALTITUDE_MAX_CLIMB" value="2."/>
+
+    <!-- auto throttle inner loop -->
+    <define name="AUTO_THROTTLE_NOMINAL_CRUISE_THROTTLE" value="0.45"/>
+    <define name="AUTO_THROTTLE_MIN_CRUISE_THROTTLE" value="0.35"/>
+    <define name="AUTO_THROTTLE_MAX_CRUISE_THROTTLE" value="0.85"/>
+    <define name="AUTO_THROTTLE_CLIMB_THROTTLE_INCREMENT" value="0.2" 
unit="%/(m/s)"/>
+    <define name="AUTO_THROTTLE_PGAIN" value="-0.023"/> <!-- -0.012 -->
+    <define name="AUTO_THROTTLE_IGAIN" value="0.01"/>
+    <define name="AUTO_THROTTLE_PITCH_OF_VZ_PGAIN" value="0.05"/>
+
+    <!-- auto pitch inner loop -->
+    <define name="AUTO_PITCH_PGAIN" value="-0.06"/> <!-- -0.03 -->
+    <define name="AUTO_PITCH_IGAIN" value="0.0"/>
+    <define name="AUTO_PITCH_MAX_PITCH" value="0.35"/>
+    <define name="AUTO_PITCH_MIN_PITCH" value="-0.35"/>
+
+    <define name="THROTTLE_SLEW" value="0.1"/>
+  </section>
+
+  <section name="HORIZONTAL CONTROL" prefix="H_CTL_">
+    <define name="COURSE_PGAIN" value="-0.9"/>
+    <define name="ROLL_MAX_SETPOINT" value="0.70" unit="radians"/> <!-- 0.5 -->
+    <define name="PITCH_MAX_SETPOINT" value="0.5" unit="radians"/>
+    <define name="PITCH_MIN_SETPOINT" value="-0.5" unit="radians"/>
+
+    <define name="ROLL_PGAIN" value="6600."/>
+    <define name="AILERON_OF_THROTTLE" value="0.0"/>
+    <define name="PITCH_PGAIN" value="-5500."/>
+    <define name="PITCH_DGAIN" value="0.4"/>
+
+    <define name="ELEVATOR_OF_ROLL" value="2400"/>
+  </section>
+
+  <section name="NAV">
+    <define name="NAV_PITCH" value="0."/>
+    <define name="NAV_GLIDE_PITCH_TRIM" value="0"/>
+  </section>
+
+  <section name="FAILSAFE" prefix="FAILSAFE_">
+    <define name="DELAY_WITHOUT_GPS" value="2" unit="s"/>
+        <define name="DEFAULT_THROTTLE" value="0.3" unit="%"/>
+        <define name="DEFAULT_ROLL" value="0.3" unit="rad"/>
+        <define name="DEFAULT_PITCH" value="0.5" unit="rad"/>
+    <define name="HOME_RADIUS" value="100" unit="m"/>
+  </section>
+
+  <section name="SIMU">
+    <define name="YAW_RESPONSE_FACTOR" value="0.5"/>
+  </section>
+
+</airframe>

Modified: paparazzi3/trunk/conf/airframes/Poine/swift_1.xml
===================================================================
--- paparazzi3/trunk/conf/airframes/Poine/swift_1.xml   2010-11-04 15:37:58 UTC 
(rev 6329)
+++ paparazzi3/trunk/conf/airframes/Poine/swift_1.xml   2010-11-04 15:39:14 UTC 
(rev 6330)
@@ -1,5 +1,153 @@
-<!-- this is a miniswift equiped with a lisa/M -->
+<!DOCTYPE airframe SYSTEM "../airframe.dtd">
 
+<!-- miniswift
+     Lisa/M board (http://paparazzi.enac.fr/wiki/Lisa)
+     XBee modem with AT firmware
+     LEA 5H GPS
+-->
+
+<airframe name="miniswift">
+
+  <firmware name="fixedwing">
+    <target name="sim"                         board="pc"/>
+    <target name="ap"                  board="lisa_m_1.0"/>
+
+    <subsystem name="radio_control"     type="ppm"/>
+    <subsystem name="telemetry"        type="transparent"/>
+    <subsystem name="control"/>
+    <subsystem name="attitude"                 type="infrared"/>
+    <subsystem name="gps"              type="ublox_lea5h"/>
+    <subsystem name="navigation"/>
+  </firmware>
+
+  <servos>
+    <servo name="MOTOR"         no="0" min="1000" neutral="1000" max="2000"/>
+    <servo name="AILEVON_LEFT"  no="1" min="1900" neutral="1521" max="1100"/>
+    <servo name="AILEVON_RIGHT" no="2" min="1100" neutral="1510" max="1900"/>
+  </servos>
+
+  <commands>
+    <axis name="THROTTLE" failsafe_value="0"/>
+    <axis name="ROLL"     failsafe_value="0"/>
+    <axis name="PITCH"    failsafe_value="0"/>
+  </commands>
+
+  <rc_commands>
+    <set command="THROTTLE" value="@THROTTLE"/>
+    <set command="ROLL"     value="@ROLL"/>
+    <set command="PITCH"    value="@PITCH"/>
+  </rc_commands>
+
+  <section name="MIXER">
+    <define name="AILEVON_AILERON_RATE" value="0.45"/>
+    <define name="AILEVON_ELEVATOR_RATE" value="0.8"/>
+  </section>
+
+  <command_laws>
+    <let var="aileron"  value="@ROLL  * AILEVON_AILERON_RATE"/>
+    <let var="elevator" value="@PITCH * AILEVON_ELEVATOR_RATE"/>
+    <set servo="MOTOR"           value="@THROTTLE"/>
+    <set servo="AILEVON_LEFT"  value="$elevator + $aileron"/>
+    <set servo="AILEVON_RIGHT" value="$elevator - $aileron"/>
+  </command_laws>
+
+  <section name="AUTO1" prefix="AUTO1_">
+    <define name="MAX_ROLL" value="RadOfDeg(50)"/>
+    <define name="MAX_PITCH" value="RadOfDeg(35)"/>
+  </section>
+
+  <section name="INFRARED" prefix="IR_">
+    <define name="ADC_IR1_NEUTRAL" value="512"/>
+    <define name="ADC_IR2_NEUTRAL" value="512"/>
+    <define name="ADC_TOP_NEUTRAL" value="512"/>
+
+    <define name="LATERAL_CORRECTION" value="-1"/>
+    <define name="LONGITUDINAL_CORRECTION" value="1"/>
+    <define name="VERTICAL_CORRECTION" value="1.5"/>
+
+    <define name="HORIZ_SENSOR_TILTED" value="1"/>
+    <define name="IR1_SIGN" value="1"/>
+    <define name="IR2_SIGN" value="-1"/>
+    <define name="TOP_SIGN" value="-1"/>
+
+    <define name="ROLL_NEUTRAL_DEFAULT" value="0" unit="deg"/>
+    <define name="PITCH_NEUTRAL_DEFAULT" value="0" unit="deg"/>
+  </section>
+
+  <section name="BAT">
+    <define name="CATASTROPHIC_BAT_LEVEL" value="9.3" unit="V"/>
+  </section>
+
+  <section name="MISC">
+    <define name="NOMINAL_AIRSPEED" value="15." unit="m/s"/>
+    <define name="CARROT" value="5." unit="s"/>
+    <define name="KILL_MODE_DISTANCE" value="(1.5*MAX_DIST_FROM_HOME)"/>
+    <define name="CONTROL_RATE" value="60" unit="Hz"/>
+
+    <define name="DEFAULT_CIRCLE_RADIUS" value="120."/>
+  </section>
+
+  <section name="VERTICAL CONTROL" prefix="V_CTL_">
+    <define name="POWER_CTL_BAT_NOMINAL" value="11.1" unit="volt"/>
+    <!-- outer loop proportional gain -->
+    <define name="ALTITUDE_PGAIN" value="-0.06"/> <!-- -0.024 -->
+    <!-- outer loop saturation -->
+    <define name="ALTITUDE_MAX_CLIMB" value="2."/>
+
+    <!-- auto throttle inner loop -->
+    <define name="AUTO_THROTTLE_NOMINAL_CRUISE_THROTTLE" value="0.45"/>
+    <define name="AUTO_THROTTLE_MIN_CRUISE_THROTTLE" value="0.35"/>
+    <define name="AUTO_THROTTLE_MAX_CRUISE_THROTTLE" value="0.85"/>
+    <define name="AUTO_THROTTLE_CLIMB_THROTTLE_INCREMENT" value="0.2" 
unit="%/(m/s)"/>
+    <define name="AUTO_THROTTLE_PGAIN" value="-0.023"/> <!-- -0.012 -->
+    <define name="AUTO_THROTTLE_IGAIN" value="0.01"/>
+    <define name="AUTO_THROTTLE_PITCH_OF_VZ_PGAIN" value="0.05"/>
+
+    <!-- auto pitch inner loop -->
+    <define name="AUTO_PITCH_PGAIN" value="-0.06"/> <!-- -0.03 -->
+    <define name="AUTO_PITCH_IGAIN" value="0.0"/>
+    <define name="AUTO_PITCH_MAX_PITCH" value="0.35"/>
+    <define name="AUTO_PITCH_MIN_PITCH" value="-0.35"/>
+
+    <define name="THROTTLE_SLEW" value="0.1"/>
+  </section>
+
+  <section name="HORIZONTAL CONTROL" prefix="H_CTL_">
+    <define name="COURSE_PGAIN" value="-0.9"/>
+    <define name="ROLL_MAX_SETPOINT" value="0.70" unit="radians"/> <!-- 0.5 -->
+    <define name="PITCH_MAX_SETPOINT" value="0.5" unit="radians"/>
+    <define name="PITCH_MIN_SETPOINT" value="-0.5" unit="radians"/>
+
+    <define name="ROLL_PGAIN" value="6600."/>
+    <define name="AILERON_OF_THROTTLE" value="0.0"/>
+    <define name="PITCH_PGAIN" value="-5500."/>
+    <define name="PITCH_DGAIN" value="0.4"/>
+
+    <define name="ELEVATOR_OF_ROLL" value="2400"/>
+  </section>
+
+  <section name="NAV">
+    <define name="NAV_PITCH" value="0."/>
+    <define name="NAV_GLIDE_PITCH_TRIM" value="0"/>
+  </section>
+
+  <section name="FAILSAFE" prefix="FAILSAFE_">
+    <define name="DELAY_WITHOUT_GPS" value="2" unit="s"/>
+        <define name="DEFAULT_THROTTLE" value="0.3" unit="%"/>
+        <define name="DEFAULT_ROLL" value="0.3" unit="rad"/>
+        <define name="DEFAULT_PITCH" value="0.5" unit="rad"/>
+    <define name="HOME_RADIUS" value="100" unit="m"/>
+  </section>
+
+  <section name="SIMU">
+    <define name="YAW_RESPONSE_FACTOR" value="0.5"/>
+  </section>
+
+</airframe>
+
+
+<!--
+
 <airframe name="miniswift 1">
 
   <commands>
@@ -34,12 +182,17 @@
     <target name="test_telemetry"      board="lisa_m_1.0">
       <param name="MODEM_PORT" value="UART2"/>
     </target>
-    <target name="test_bmp085"         board="lisa_m_1.0">
-      <param name="MODEM_PORT" value="UART2"/>
-    </target>
+    <target name="test_bmp085"         board="lisa_m_1.0"/>
     <target name="test_esc_mkk_simple" board="lisa_m_1.0"/>
     <target name="test_rc_spektrum"    board="lisa_m_1.0"/>
     <target name="test_manual"         board="lisa_m_1.0"/>
+    <target name="test_esc_mkk_simple" board="lisa_m_1.0"/>
+    <target name="test_hmc5843"        board="lisa_m_1.0"/>
+    <target name="test_itg3200"        board="lisa_m_1.0"/>
+    <target name="test_adxl345"        board="lisa_m_1.0"/>
+    <target name="test_adc"            board="lisa_m_1.0"/>
   </firmware>
 
-</airframe>
\ No newline at end of file
+</airframe>
+
+ -->
\ No newline at end of file
reply via email to
[Prev in Thread] Current Thread [Next in Thread]