T U-Boot 1.1.3 (Apr 18 2007 - 10:56:24) MPC8272 Reset Status: External Soft, External Hard MPC8272 Clock Configuration - Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300 - dfbrg 1, corecnf 0x1a, busdf 3, cpmdf 1, plldf 0, pllmf 3 - vco_out 400000000, scc_clk 100000000, brg_clk 25000000 - cpu_clk 400000000, cpm_clk 200000000, bus_clk 100000000 - pci_clk 33333333 CPU: MPC8272 (HiP7 Rev 14, Mask 1.0 1K50M) at 400 MHz Board: Compulab CM-F82 DRAM: 128 MB FLASH: 4 MB In: serial Out: serial Err: serial GFX: ................................................................................................................................2700G graphics controller without external memory is available ................................................................NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Net: FCC2 ETHERNET Date: 2070-01-01 (Thursday) Time: 8:19:51 Hit any key to stop autoboot: 1  0 cm-f82> setenv serverip 192.168.151.119;\tftp 0x4000 los178.ram.img Using FCC2 ETHERNET device TFTP from server 192.168.151.119; our IP address is 192.168.151.173 Filename 'los178.ram.img'. Load address: 0x4000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################### done Bytes transferred = 11198464 (aae000 hex) cm-f82> go 0x5020 ## Starting application at 0x00005020 ... RAM:64M NOR:0M NAND:0M NVM:8K IO-A:0M IO-B:0M BUS:25MHz CPU:100MHz permap_size 0x1c00000 perlimit_end 0x9e400000 kseg_size 0x4000000 Using V3020 RTC ver 0.01 kmidrvinstall: Device is installed with info->size value 52 kmidrvinstall: install start init device kmidrvinstall: semaphores init kmidrvinstall: registers init kmidrv: install exits module fatal offset 0x1040 Current mode is 0 Started on Partition 0 Started on Partition 1 Started on Partition 2 Started on Partition 3 Started on Partition 4 Started on Partition 5 Started on Partition 6 Started on Partition 7 Started on Partition 8 Started on Partition 9 Started on Partition 10 Started on Partition 11 Started on Partition 12 Started on Partition 13 Started on Partition 14 Started on Partition 15 LynxOS-178 Version 2.1.0 (PowerPC) Copyright 2002-2005 LynuxWorks, Inc. All rights reserved. (LynuxWorks' copyright applies to the entire LynxOS-178 produhmct a_nd isupeorsedes the copyrcighttl stateme(mint included nin iorndividual files) Copyright 20Dev00-2002 Rock=1well Collins Inc. A,ll r cights reoserved. LynxOS-17m8 (ppc) created mWed May 12 14:55a:35 201nd0 cini=t: C2onnecting to0 hea)lth monitor cinit: Processing arguments cinit: Mounting ROFS cinit: Reading normal VCT cinit: VCT CRC in VCT is cinit: converted VCT CRC is 0x0 cinit: VCT CPN is 104-1234-002 cinit: Gathering VM info cinit: Loading drivers cinit: Reading Filesystem Info cinit: Default priority is 16 cinit: Starting scheduler cinit: Waiting for termination PI-171 start script (2008_09_12) starting PI-171 program... setsid: Not owner Welcome to LynxOS-178 (VM0) (Normal mode) [System: /] $