[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Ltib] Cannot build e2fsprogs using ./ltib --force
From: |
Stuart Hughes |
Subject: |
Re: [Ltib] Cannot build e2fsprogs using ./ltib --force |
Date: |
Fri, 06 Jun 2008 14:06:20 +0100 |
Hi James,
I got a copy of LTIB from that release date and I've not been able to
reproduce the problem. That's probably because I don't have the same
distro to test on, for Ubuntu's I've only got 8.04.
I did a bit of googling and this looks relevant:
http://www.linuxarkivet.se/mlists/ext3-users/0404/msg00006.html
When you say it works the first time but after a re-build, did you mean
that it worked when you first installed (e.g. using the pre-built rpms
from the ISO image)?
Can you try patching the spec file with this:
--- dist/lfs-5.1/e2fsprogs/e2fsprogs.spec.orig 2008-06-06 12:02:11.000000000
+0100
+++ dist/lfs-5.1/e2fsprogs/e2fsprogs.spec 2008-06-06 14:02:09.000000000
+0100
@@ -36,7 +36,7 @@
# cp: cannot create regular file `libintl.h': Permission denied
chmod +w intl/libintl.h
CC="gcc" BUILD_CC="$BUILDCC" \
-./configure --enable-dynamic-e2fsck --enable-elf-shlibs --prefix=%{_prefix}
--host=$CFGHOST --mandir=%{_mandir}
+./configure --enable-dynamic-e2fsck --enable-elf-shlibs --prefix=%{_prefix}
--host=$CFGHOST --mandir=%{_mandir} --disable-nls
make -j1 libs progs docs
%Install
It turns of nls which I think should fix your problem.
Regards, Stuart
On Thu, 2008-06-05 at 13:31 -0700, James E. Chargin Jr. wrote:
> Stuart,
>
> Thanks for helping out.
>
> As you requested, I have run the several commands you provided. The
> first four command completed without complaint, but the final "./ltib"
> failed, with the same symptom as before. Part of the output follows:
> ----
> ...
> make[1]: Leaving directory
> `/home/jimc/.../ltib-mpc8315erdb-20071129/rpm/BUILD/e2fsprogs-1.34/tests/progs'
> making all in po
> make[1]: Entering directory
> `/home/jimc/.../ltib-mpc8315erdb-20071129/rpm/BUILD/e2fsprogs-1.34/po'
> : --update cs.po e2fsprogs.pot
> rm -f cs.gmo && : -c --statistics -o cs.gmo cs.po
> mv: cannot stat `t-cs.gmo': No such file or directory
> mane[1]: *** [cs.gmo] Error 1
> make[1]: Leaving directory
> `/home/jimc/.../ltib-mpc8315erdb-20071129/rpm/BUILD/e2fsprogs-1.34/po'
> make: *** [all-progs-recursive] Error 1
> error: Bad exit status from
> /home/jimc/.../ltib-mpc8315erdb-20071129/tmp/rpm-tmp.95834 (%build)
>
> RPM build errors:
> Bad exit status from
> /home/jimc/.../ltib-mpc8315erdb-20071129/tmp/rpm-tmp.95834 (%build)
> Build time for e2fsprogs: 45 seconds
>
> Failed building e2fsprogs
>
>
> f_buildrpms() returned an error, exiting
>
> Started: Thu Jun 5 12:07:30 2008
> Ended: Thu Jun 5 13:08:19 2008
> Elapsed: 49 seconds
>
> These packages failed to build:
> e2fsprogs
> Build Failed
>
> Exiting on error or interrupt
> ----
>
> Because this command failed, I didn't even run the "./ltib -p e2fsprogs
> -f" you requested.
>
> Again, thanks for the help. What more can I do to help determine what
> the problem might be?
>
> Regards,
> Jim
> ---
> James E. Chargin Jr.
> Sierra Design Associates (530) 478-6689
> 117 New Mohawk Rd, Suite H address@hidden
> Nevada City, CA 95959 USA http:\\www.sdateam.com
>
>
> Stuart Hughes wrote:
> > Hi Jim,
> >
> > The most likely explanation is that is built after e2fsprogs is detected
> > on subsequent rebuilds of e2fsprogs, thus causing a failure. I may need
> > to exclude this using an explicity ac_cv_...=no
> >
> > Can you try this for me:
> >
> > $ ./ltib -m clean
> > $ rm -rf rpm/BUILD/e2fs*
> > $ touch dist/lfs-5.1/e2fsprogs/e2fsprogs.spec
> > $ ./ltib
> >
> > If this works but a subsequent: ./ltib -p e2fsprogs -f fails then I'll
> > have something to hunt down.
> >
> > Regards, Stuart
> >
> > On Wed, 2008-06-04 at 11:36 -0700, James E. Chargin Jr. wrote:
> >> I'm building for the 8513erdb, on Ubuntu 7.10.
> >>
> >> Previous attempts to build via ltib have succeeded.
> >>
> >> Out of curiosity, I ran ltib with the --force option. Now,
> >> e2fsprogs-1.34 will not build. The only way I can get a successful build
> >> is by excluding e2fsprogs, which is not acceptable for the long term.
> >>
> >> The following is among the output generated during the build failure
> >> ----
> >> make[1]: Leaving directory
> >> `/home/jimc/.../ltib-mpc8315erdb-20071129/rpm/BUILD/e2fsprogs-1.34/resize'
> >> making all in tests/progs
> >> make[1]: Entering directory
> >> `/home/jimc/.../ltib-mpc8315erdb-20071129/rpm/BUILD/e2fsprogs-1.34/tests/progs'
> >> gcc -o test_icount test_icount.o test_icount_cmds.o
> >> ../../lib/libext2fs.so ../../lib/libss.so ../../lib/libcom_err.so
> >> make[1]: Leaving directory
> >> `/home/jimc/.../ltib-mpc8315erdb-20071129/rpm/BUILD/e2fsprogs-1.34/tests/progs'
> >> making all in po
> >> make[1]: Entering directory
> >> `/home/jimc/.../ltib-mpc8315erdb-20071129/rpm/BUILD/e2fsprogs-1.34/po'
> >> : --update cs.po e2fsprogs.pot
> >> rm -f cs.gmo && : -c --statistics -o cs.gmo cs.po
> >> mv: cannot stat `t-cs.gmo': No such file or directory
> >> make[1]: *** [cs.gmo] Error 1
> >> make[1]: Leaving directory
> >> `/home/jimc/.../ltib-mpc8315erdb-20071129/rpm/BUILD/e2fsprogs-1.34/po'
> >> make: *** [all-progs-recursive] Error 1
> >> error: Bad exit status from
> >> /home/jimc/.../ltib-mpc8315erdb-20071129/tmp/rpm-tmp.80089 (%build)
> >>
> >>
> >> RPM build errors:
> >> Bad exit status from
> >> /home/jimc/.../ltib-mpc8315erdb-20071129/tmp/rpm-tmp.80089 (%build)
> >> Build time for e2fsprogs: 38 seconds
> >>
> >> Failed building e2fsprogs
> >>
> >>
> >> f_buildrpms() returned an error, exiting
> >>
> >> Started: Wed Jun 4 11:16:05 2008
> >> Ended: Wed Jun 4 11:17:01 2008
> >> Elapsed: 56 seconds
> >>
> >> These packages failed to build:
> >> e2fsprogs
> >> Build Failed
> >>
> >> Exiting on error or interrupt
> >> ----
> >>
> >> I think the failing line seems to want to call msgfmt, which should be a
> >> part of the gettext package. I've got gettext installed and when I
> >> previously ran ltib without --force, it built successfully.
> >>
> >> What am I missing here, or what should I try to get this working as
> >> expected?
> >>
> >> Thanks,
> >> Jim
> >
> >
- [Ltib] Cannot build e2fsprogs using ./ltib --force, James E. Chargin Jr., 2008/06/04
- Re: [Ltib] Cannot build e2fsprogs using ./ltib --force, Stuart Hughes, 2008/06/05
- Re: [Ltib] Cannot build e2fsprogs using ./ltib --force, James E. Chargin Jr., 2008/06/05
- Re: [Ltib] Cannot build e2fsprogs using ./ltib --force,
Stuart Hughes <=
- Re: [Ltib] Cannot build e2fsprogs using ./ltib --force, James E. Chargin Jr., 2008/06/06
- Re: [Ltib] Cannot build e2fsprogs using ./ltib --force, Stuart Hughes, 2008/06/06
- Re: [Ltib] Cannot build e2fsprogs using ./ltib --force, James E. Chargin Jr., 2008/06/06
- Re: [Ltib] Cannot build e2fsprogs using ./ltib --force, Stuart Hughes, 2008/06/06
- Re: [Ltib] Cannot build e2fsprogs using ./ltib --force, James E. Chargin Jr., 2008/06/06