[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: GuixSD is missing /dev/disk/by-uuid
From: |
Chris Marusich |
Subject: |
Re: GuixSD is missing /dev/disk/by-uuid |
Date: |
Sun, 14 Feb 2016 14:42:38 -0800 |
User-agent: |
Gnus/5.13 (Gnus v5.13) Emacs/24.5 (gnu/linux) |
Hi,
I ran those commands, and it fixed the problem: /dev/disk/by-uuid now
exists and contains the links I expected to see.
However, it introduced a new problem. Now, my network interface eth0
does not show up like it did before. For example, when I run ifconfig,
"lo" shows up but "eth0" is missing. Nothing that relies on the network
works.
I've compared /var/log/messages before and after. Before the
reconfigure, it contained the following messages from "b44" (I think
this is my ethernet driver). This seems to show eth0 being successfully
set up:
--8<---------------cut here---------------start------------->8---
Feb 14 12:52:44 localhost vmunix: [ 8.172311] b44: Broadcom 44xx/47xx 10/100
PCI ethernet driver version 2.0
Feb 14 12:52:44 localhost vmunix: [ 8.192588] b44 ssb0:0 eth0: Broadcom
44xx/47xx 10/100 PCI ethernet driver 00:19:b9:7e:b4:cd
Feb 14 12:52:48 localhost vmunix: [ 45.812218] b44 ssb0:0 eth0: Link is up at
100 Mbps, full duplex
Feb 14 12:52:48 localhost vmunix: [ 45.812226] b44 ssb0:0 eth0: Flow control
is off for TX and off for RX
Feb 14 12:52:48 localhost vmunix: [ 55.223285] b44 ssb0:0 eth0: powering down
PHY
Feb 14 12:52:48 localhost vmunix: [ 55.252555] b44 ssb0:0 eth0: powering down
PHY
Feb 14 12:52:52 localhost vmunix: [ 61.812216] b44 ssb0:0 eth0: Link is up at
100 Mbps, full duplex
Feb 14 12:52:52 localhost vmunix: [ 61.814593] b44 ssb0:0 eth0: Flow control
is off for TX and off for RX
--8<---------------cut here---------------end--------------->8---
However, after the upgrade, I only see the following messages:
--8<---------------cut here---------------start------------->8---
Feb 14 12:12:16 localhost vmunix: [ 10.820248] b44: Broadcom 44xx/47xx 10/100
PCI ethernet driver version 2.0
Feb 14 12:12:16 localhost vmunix: [ 10.848595] b44 ssb0:0 eth0: Broadcom
44xx/47xx 10/100 PCI ethernet driver 00:19:b9:7e:b4:cd
--8<---------------cut here---------------end--------------->8---
I've checked messages, dmd.log, and shepherd.log in /var/log/, but I
can't figure out why networking isn't working. I found a similar problem
on the Guix bug tracker:
https://debbugs.gnu.org/cgi/bugreport.cgi?bug=18483
However, I don't see messages like those in my logs, so I'm not sure
it's the same problem.
How can I proceed? My goal is to make networking work, like it did
before the reconfigure. I don't think I can use the new version of guix
until I get this networking problem fixed. Any advice would be
appreciated.
Thank you,
Chris