Re: gnokiid AT command reference

[Daniele Forsi]

Here is the first draft of gnokiid AT command reference.
I think it should be more verbose tags. Comments are welcome.

Daniele
=====
AT command reference for gnokiid 0.6.4
Draft 1 01-feb-2005 by Daniele Forsi

AT* Read SMS
AT# Set/Get caller ID mode
AT+ Get phone information
ATA Answer call
ATD Dial number
ATE Set echo on/off
ATH Hang up call
ATI Get modem information
ATQ Set quiet mode on/off
ATS Set/Get S-register value
ATV Set verbose on/off
ATX Choose connect messages
ATZ Reset modem


AT*
Extended commands "*"

AT*NOKIATEST
This command is ignored.

AT*C
Start reading SMS messages

After AT*C modem responds with OK, then the following commands are accepted: 
DIR, EXIT, HELP.

After sending the DIR command you can type the following key followed by the 
Enter key:
                P: show previous SMS
                N: show next SMS
                D: delete current SMS
                Q: quit to AT*C mode

HELP shows this message:
The following commands work...
DIR
EXIT
HELP

EXIT: exit to command mode


AT# Extended commands "#"

AT#CID Set/Get Caller ID mode

AT#CID? Print current settings
AT#CID=<n>
        <n>: 0 Disable caller ID (default)
        <n>: 1 Enable formatted caller ID
AT#CID=? Print supported settings, currently (0,1)
Note: when caller ID is disabled application gets only one RING, when it is 
enabled it gets one RING, then caller ID data, then a second RING


AT+
Extended commands "+"

AT+C
Extended commands "+C"

AT+CSQ
Get RF Level
<code>
AT+CSQ
+CSQ: 31, 99
OK
</code>
First number is SQM (Signal Quality Measurement) range is 0..31 or 99 if not 
known or not detectable
Second number is FER (Frame Error Rate) range is 0..7 or 99 if not known or 
not detectable (in this version it is always 99)

AT+CGMI
Print manufacturer information
<code>
AT+CGMI
Nokia Mobile Phones
OK
</code>

AT+CGSN
Print IMEI
<code>
AT+CGSN
350601234567890
OK
</code>

AT+CGMR
Print hardware revision
<code>
AT+CGMR
SW 04.30, HW 0911
OK
</code>

AT+CGMM
Print model code 
<code>
AT+CGMM
NHM-6
OK
</code>

AT+CMGD Delete SMS
        AT+CMGD=<n>
        <n>: message number
AT+CMGF Select SMS format
        AT+CMGF=<n>
                0: PDU_MODE (default)
                1: TEXT_MODE
        AT+CMGF? Show current format; only TEXT_MODE is supported by AT+CMGL
AT+CMGR Read SMS message
        AT+CMGR=<n>
        <n>: message number
AT+CMGS Send SMS
        AT+CMGS="<n>"
        <n>: destination phone number (quotes are mandatory)
        CTRL+Z to send, ESC to abort
AT+CMGL List SMS
        AT+CMGL=<stat>
                <stat>: (empty) 1 3 "REC READ" "REC SENT" 
                0 2 "REC UNREAD" "REC UNSENT" 
                4 "ALL"
Note: quotes are mandatory


AT+G
Extended commands "+G"

AT+GMI Print manufacturer information for the TA (Terminal Adaptor)
                Hugh Blemings, Pavel Janik ml. and others...

AT+GMR Print revision information for the TA (Terminal Adaptor)
gnokiid version, compile date and time
<code>
AT+GMR
0.6.4 10:49:37 Jan 31 2005
OK
</code>

AT+GMM Print model information for the TA (Terminal Adaptor)
The string is "gnokii configured on %s for models %s"
<code>
AT+GMM
gnokii configured on /dev/ttyS0 for models 
6110|6130|6150|6190|5110|5130|5190|31
OK
</code>

AT+GSN
Print serial number for the TA (Terminal Adaptor)
<code>
AT+GSN
none built in, choose your own
OK
</code>


ATA
Answer call

Answer incoming call


D
Dial number

"T" and "P" are ignored, all subsequent characters are passed to phone
Before dialing you must set S35 == 0 for DigitalData mode or S35 != 0 for 
NonDigitalData mode.
; is not supported
(FIXME: ATD needs a better explanation)


ATE
Set character echo on or off

ATE, ATE0 local echo off
ATE1 local echo on (default)
Sets bit 2 of register S14


ATH
Modem on/off hook

ATH, ATH0 hang up current call
ATH1 do nothing


ATI
Get modem information

ATI<n>
        <n>: 0..4
ATI, ATI0:      /* Print terminal id (print register S39 as decimal) */
ATI0
0
OK

ATI1:   /* Print serial number (IMEI) */

Read from phone
ATI1
350601234567890
OK

ATI2: /* Print phone revision */

Read from phone
ATI2
SW 04.30, HW 0911
OK

ATI3: /* Print modem revision */
        gnokiid version
ATI3
gnokiid 0.6.4
OK

ATI4: /* Print OEM string */

Read from phone
ATI4
Nokia NHM-6
OK


ATQ
Set results on or off

ATQ, ATQ0 quiet off, print results according to ATV (default)
ATQ1 quiet on, print nothing
Sets bit 4 of register S14
This command is ignored.


ATS
Set or get S-register value

ATS<r>?
Print current value of register

ATS<r>=<v> Set register <r> to value <v>
        <r>: 0..101
        <v>: 0..255
To enable auto answer use ATS0=<v> where <v> is a number greater than zero; 
use ATS0=0 to disable auto answer.
Note: when auto answer is enabled phone responds immediatly ignoring the value 
of <v>.


ATV
Set verbosity level

ATV, ATV0 verbose off, modem responds with numbers (0, 4)
ATV1 verbose on, modem responds with words (OK, ERROR) (default)
Set bit 8 of register S14. This does not affect extended commands.


ATX
Set verbosity of connect messages

ATX<n>
<n> 0..5
Set register S22
This command is ignored.


ATZ
Reset modem and load stored profile

ATZ, ATZ0, ATZ1 all load the same profile
ATS0=0S1=0S2=43S3=10S4=13S5=8S35=7ATQ1E1S100=26S101=27
Other registers are set to zero.
This only resets the virtual modem and not the phone.

[eof]