--- Begin Message ---
Subject: |
[core-updates] gawk fails test suite on armhf |
Date: |
Tue, 19 Dec 2017 18:34:21 -0500 |
On core-updates, 'gawk' fails to build on armhf:
https://hydra.gnu.org/build/2392045
Here's the tail of the build log:
--8<---------------cut here---------------start------------->8---
make[2]: Entering directory '/tmp/guix-build-gawk-4.1.4.drv-0/gawk-4.1.4/test'
1 TESTS FAILED
make[2]: *** [Makefile:4128: pass-fail] Error 1
make[2]: Leaving directory '/tmp/guix-build-gawk-4.1.4.drv-0/gawk-4.1.4/test'
make[2]: Entering directory '/tmp/guix-build-gawk-4.1.4.drv-0/gawk-4.1.4/test'
for i in _* ; \
do \
if [ "$i" != "_*" ]; then \
echo ============== $i ============= ; \
base=`echo $i | sed 's/^_//'` ; \
if [ -r ${base}.ok ]; then \
diff -c ${base}.ok $i ; \
else \
diff -c "."/${base}.ok $i ; \
fi ; \
fi ; \
done
============== _pty1 =============
*** pty1.ok 2014-01-20 19:53:01.000000000 +0000
--- _pty1 2017-12-19 09:34:25.516824947 +0000
***************
*** 1,2 ****
! 123
! x is abc
--- 1,4 ----
! sh: /dev/tty: No such device or address
! sh: /dev/tty: No such device or address
! x is
! x is
make[2]: *** [Makefile:4137: diffout] Error 1
make[2]: Leaving directory '/tmp/guix-build-gawk-4.1.4.drv-0/gawk-4.1.4/test'
make[1]: *** [Makefile:1651: check] Error 1
make[1]: Leaving directory '/tmp/guix-build-gawk-4.1.4.drv-0/gawk-4.1.4/test'
make: *** [Makefile:742: check-recursive] Error 1
phase `check' failed after 49.9 seconds
builder for `/gnu/store/9f8adlrb6y8f1q0zfzk49x05ly4r6lp4-gawk-4.1.4.drv' failed
with exit code 1
@ build-failed /gnu/store/9f8adlrb6y8f1q0zfzk49x05ly4r6lp4-gawk-4.1.4.drv - 1
builder for `/gnu/store/9f8adlrb6y8f1q0zfzk49x05ly4r6lp4-gawk-4.1.4.drv' failed
with exit code 1
--8<---------------cut here---------------end--------------->8---
Mark
--- End Message ---
--- Begin Message ---
Subject: |
Re: bug#29776: [core-updates] gawk fails test suite on armhf |
Date: |
Wed, 20 Dec 2017 17:53:08 -0500 |
User-agent: |
Gnus/5.13 (Gnus v5.13) Emacs/25.3 (gnu/linux) |
Marius Bakke <address@hidden> writes:
> Mark H Weaver <address@hidden> writes:
>
>> On core-updates, 'gawk' fails to build on armhf:
>>
>> https://hydra.gnu.org/build/2392045
>
> I tried restarting this (again), and it succeeded:
>
> https://hydra.gnu.org/build/2392045
>
> Maybe there's something specific to hydra-slave3, which had failed three
> times in a row? The successful build came from hydra-slave1.
You're right. hydra-slave3's kernel was in a bad state, with lots of
errors in the 'dmesg' output about unaligned accesses. I rebooted it.
I'm closing this bug now.
Thanks!
Mark
--- End Message ---