hi, what's 2DCT_or_3DCT?
Best regards,
Marcus
On Sat, 2019-05-25 at 19:38 +0100, farid mihoub wrote:
My application is to broadcast a video using softcast approach.
Video-->2DCT_or_3DCT-->Floating coefficients-->complex_mapping
-->ofdm_phy
My video quality (PSNR) will depend linearly to my SNR so no need to
have an adaptive modulation.
25.05.2019, 18:27, "Marcus Müller" <address@hidden>:
> 1- So, you have an SNR of best-case 16 dB; that's not high for an
> OFDM
> system.
>
> 2- No, there's no power normalization. Hint: you can look all this
> up
> by actually looking inside these blocks! This would make a lot of
> sense, since it sounds you don't actually want to use tzhe OFDM
> blocks
> at all. The whole advantage of the OFDM blocks compared to just
> doing
> an IFFT of your transmit vector is that you get a header and
> modulation
> scheme.
>
> 3- Not quite sure what "information is linearly related to complex
> symbols" means? Can you elaborate?
> 3b- A case where you *don't* do FEC is either a non-communications
> system (i.e. you don't actually want to do OFDM for the reason of
> transmitting information) or the extremely-bad-SNR case (where FEC
> makes your BER better). For both cases, the existing OFDM blocks
> are
> more of an obstacle than a solution.
>
> What are you building? What is your overall application. Please
> paint
> the bigger picture – it's a bit frustrating to try to help you, but
> then only get told that "this is not how I want to do it".
>
> Best regards,
> Marcus
>
> On Sat, 2019-05-25 at 18:39 +0200, Marcus Müller wrote:
> > Dear Farid,
> >
> > please always respond on the mailing list.
> > Thank you,
> > Marcus Müller
> >
> > On Sat, 2019-05-25 at 17:36 +0100, farid mihoub wrote:
> > > 1- For the noise : in the TX side the output is in the order
> > of 2A,
> > > the noise 0.05A.
> > > 2-Second even without noise, the const does not affect the
> > > transmission, is there any sort of power normalization?
> > > 3-For the FEC and the modulation I want to try my custom
> > mapping
> > > where information is linearly related to complex symbols, and
> > my
> > > application doesn't require error correction.
> > >
> > > Thank you.
> > >
> > >
> > > 25.05.2019, 17:06, "Marcus Müller" <address@hidden>:
> > > > Hello Farid,
> > > > On Sat, 2019-05-25 at 15:59 +0100, farid mihoub wrote:
> > > > > Hello,
> > > > >
> > > > > In the OFDM_tx, rx examples in gr-digital :
> > > > > 1- Why just a low level of noise affect the transmission
> > and
> > > > > cause it
> > > > > to stop.
> > > >
> > > > "low" is relative. It seems it's high enough to cause packet
> > > > losses,
> > > > iff it's actually the noise.
> > > >
> > > > > 2- in the the Tx output and the Rx input no matter the
> > value
> > > > > of
> > > > > the
> > > > > multiply constant we apply
> > > > > that would not affect our transmission.
> > > >
> > > > Then it's probably not only the noise!
> > > >
> > > > > 3- Is there any way to separate channel estimation and
> > > > > tracking
> > > > > from
> > > > > data transmission, sometime I get the error "invalid
> > packet
> > > > > detected!" form the packet parser, also I need my data to
> > > > > bypass
> > > > > FEC
> > > > > and QAM.
> > > >
> > > > Um, prior to QAM demodulation there is no data, and prior to
> > FEC
> > > > decoding there is no information bits, so I'm not sure what
> > you
> > > > want?
> > > >
> > > > > My purpose is to stream raw complex data to the I/Q
> > > > > components
> > > > > directly.
> > > >
> > > > Then it seems you don't want an OFDM transceiver but maybe
> > just
> > > > simply
> > > > a single IFFT? Not quite sure what you have in mind.
> > > >
> > > > Best regards,
> > > > Marcus
> > > >
> >
> > _______________________________________________
> > Discuss-gnuradio mailing list
> > address@hidden
> > https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
_______________________________________________
Discuss-gnuradio mailing list
address@hidden
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio