[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Discuss-gnuradio] USRP Source Block error 255
|
From: |
Chad Spooner |
|
Subject: |
[Discuss-gnuradio] USRP Source Block error 255 |
|
Date: |
Tue, 7 Aug 2018 11:54:05 -0700 |
|
User-agent: |
Mozilla/5.0 (X11; Linux x86_64; rv:52.0) Gecko/20100101 Thunderbird/52.9.1 |
All:
I'm having trouble with some flowgraphs under Ubuntu 18.04.1. I recently
set up a HP ZBook G3
with that OS and did a PyBOMBS install of gnuradio and UHD. I'm
connected to an Ettus X310
and the SBX daughter card here.
I then starting running some of the flowgraphs I had been running under
16.04 on that same
computer. I hadn't observed any errors with these flowgraphs under 16.04.
After running for a while, I get the following error:
gr::log :WARN: gr uhd usrp source0 - USRP Source Block caught rx error
code: 255
The flowgraph doesn't appear to stop, but the graphics I'm running using
QT GUI Vector Sink
freeze up. I can then stop the flowgraph in the usual way by clicking
the "kill the flowgraph"
button.
kernel: 4.15.0-29-generic #31-Ubuntu SMP
gnuradio version: 3.7.12.0
UHD version: UHD_3.14.0.0-31-g98057752
Any ideas of how to fix this problem?
Here is the output of uhd_usrp_probe:
[INFO] [UHD] linux; GNU C++ version 7.3.0; Boost_106501;
UHD_3.14.0.0-31-g98057752
[INFO] [X300] X300 initialization sequence...
[INFO] [X300] Maximum frame size: 1472 bytes.
[INFO] [X300] Radio 1x clock: 200 MHz
[INFO] [0/DmaFIFO_0] Initializing block control (NOC ID: 0xF1F0D00000000000)
[INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1300 MB/s)
[INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1303 MB/s)
[INFO] [0/Radio_0] Initializing block control (NOC ID: 0x12AD100000000001)
[INFO] [0/Radio_1] Initializing block control (NOC ID: 0x12AD100000000001)
[INFO] [0/DDC_0] Initializing block control (NOC ID: 0xDDC0000000000000)
[INFO] [0/DDC_1] Initializing block control (NOC ID: 0xDDC0000000000000)
[INFO] [0/DUC_0] Initializing block control (NOC ID: 0xD0C0000000000000)
[INFO] [0/DUC_1] Initializing block control (NOC ID: 0xD0C0000000000000)
_____________________________________________________
/
| Device: X-Series Device
| _____________________________________________________
| /
| | Mboard: X310
| | revision: 6
| | product: 30410
| | mac-addr0: 00:80:2f:19:13:0a
| | mac-addr1: 00:80:2f:19:13:0b
| | gateway: 192.168.10.1
| | ip-addr0: 192.168.10.2
| | subnet0: 255.255.255.0
| | ip-addr1: 192.168.20.2
| | subnet1: 255.255.255.0
| | ip-addr2: 192.168.30.2
| | subnet2: 255.255.255.0
| | ip-addr3: 192.168.40.2
| | subnet3: 255.255.255.0
| | serial: 306B4B8
| | FW Version: 6.0
| | FPGA Version: 35.1
| | FPGA git hash: a20b791
| | RFNoC capable: Yes
| |
| | Time sources: internal, external, gpsdo
| | Clock sources: internal, external, gpsdo
| | Sensors: ref_locked
| | _____________________________________________________
| | /
| | | RX Dboard: A
| | | ID: WBX-120, WBX-120 + Simple GDB (0x0081)
| | | Serial: F5FB72
| | | _____________________________________________________
| | | /
| | | | RX Frontend: 0
| | | | Name: WBX-120 RX+GDB
| | | | Antennas: TX/RX, RX2, CAL
| | | | Sensors: lo_locked
| | | | Freq range: 25.000 to 2200.000 MHz
| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
| | | | Bandwidth range: 120000000.0 to 120000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Codec: A
| | | | Name: ads62p48
| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB
| | _____________________________________________________
| | /
| | | RX Dboard: B
| | | ID: SBX-120 (0x0083)
| | | Serial: F5B3A8
| | | _____________________________________________________
| | | /
| | | | RX Frontend: 0
| | | | Name: SBX-120 RX
| | | | Antennas: TX/RX, RX2, CAL
| | | | Sensors: lo_locked
| | | | Freq range: 400.000 to 4400.000 MHz
| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
| | | | Bandwidth range: 120000000.0 to 120000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | RX Codec: B
| | | | Name: ads62p48
| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB
| | _____________________________________________________
| | /
| | | TX Dboard: A
| | | ID: WBX-120 (0x0080)
| | | Serial: F5FB72
| | | ID: WBX + Simple GDB, WBX v3 + Simple GDB, WBX v4 + Simple
GDB, WBX-120 + Simple GDB (0x004f)
| | | Serial: F5E6B6
| | | _____________________________________________________
| | | /
| | | | TX Frontend: 0
| | | | Name: WBX-120 TX+GDB
| | | | Antennas: TX/RX, CAL
| | | | Sensors: lo_locked
| | | | Freq range: 25.000 to 2200.000 MHz
| | | | Gain range PGA0: 0.0 to 31.0 step 1.0 dB
| | | | Bandwidth range: 120000000.0 to 120000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | TX Codec: A
| | | | Name: ad9146
| | | | Gain Elements: None
| | _____________________________________________________
| | /
| | | TX Dboard: B
| | | ID: SBX-120 (0x0082)
| | | Serial: F5B3A8
| | | _____________________________________________________
| | | /
| | | | TX Frontend: 0
| | | | Name: SBX-120 TX
| | | | Antennas: TX/RX, CAL
| | | | Sensors: lo_locked
| | | | Freq range: 400.000 to 4400.000 MHz
| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
| | | | Bandwidth range: 120000000.0 to 120000000.0 step 0.0 Hz
| | | | Connection Type: QI
| | | | Uses LO offset: No
| | | _____________________________________________________
| | | /
| | | | TX Codec: B
| | | | Name: ad9146
| | | | Gain Elements: None
| | _____________________________________________________
| | /
| | | RFNoC blocks on this device:
| | |
| | | * DmaFIFO_0
| | | * Radio_0
| | | * Radio_1
| | | * DDC_0
| | | * DDC_1
| | | * DUC_0
| | | * DUC_1
Thanks much,
Chad
- [Discuss-gnuradio] USRP Source Block error 255,
Chad Spooner <=