Re: [Discuss-gnuradio] GNU Radio on Zedboard

[Philip Balister]

On 03/19/2015 10:48 AM, Alireza Khodamoradi wrote:
> Here are the files I have in the FAT partition (boot):
> 
> 1- boot.bin
> 2- u-boot.img
> 3- uEnv.txt
> 4- uImage
> 5- zc702-zynq7.dtb
> 
> * I used this image: *sdimage-8G-zc702.direct*

So this all looks correct. When you put the card in the PC both the FAT
and roofs partitions are mounted OK? You did use an 8G card?

I'm not sure what to say at this point. Everything looks OK. I am
traveling and away from borads for a few weeks.

Philip

> 
> On Thu, Mar 19, 2015 at 6:41 AM, Philip Balister <address@hidden>
> wrote:
> 
>> On 03/18/2015 10:44 PM, Alireza Khodamoradi wrote:
>>> Philip,
>>>
>>> Thank you for letting me using your images. I tried both of them with
>> the *dd
>>> *command, it took me around 2000 seconds (30 mins) each and after using
>>> them on the board I get the following message via the UART:
>>>
>>> *U-Boot SPL 2014.01 (Jan 09 2015 - 20:24:45)*
>>> *mmc boot*
>>> *reading fpga.bin*
>>> *spl: error reding image fpga.bin, err - -1*
>>> *reading system.dtb*
>>> *spl: error reading image system.dtb, err - -1*
>>> *reading u-boot.img*
>>> *spl: error reading image u-boot.img, err - -1*
>>> *### ERROR ### Please RESET the board ###*
>>
>> So the first stage boot loader is running, which is good.
>>
>> It looks for a couple of files which should be there, which is OK.
>> (fpga.bin and system.dtb)
>>
>> Then it tries to load u-boot.img which it doesn't find. This is bad.
>>
>> Can you put the card in a PC and send the list of file in the FAT
>> partition?
>>
>> Philip
>>
>>
>>>
>>> I got the above message for sdimage-8G-zc702.direct. I get no message for
>>> the other image.
>>>
>>> What am I doing wrong?
>>>
>>> On Fri, Mar 13, 2015 at 11:22 AM, Philip Balister <address@hidden>
>>> wrote:
>>>
>>>> On 03/13/2015 01:17 PM, Alireza Khodamoradi wrote:
>>>>> Hello everyone,
>>>>>
>>>>> I'm going through the instructions from here:
>>>>>
>>>>> http://gnuradio.org/redmine/projects/gnuradio/wiki/Zynq
>>>>
>>>> I should go over those carefully, but in the mentime I have some images
>>>> built for the zedbaord here:
>>>>
>>>>
>> https://www.dropbox.com/sh/yfbpj63pcenqatr/AAAt0s3xFXs47I7q5pNopheHa?dl=0
>>>>
>>>> Take the zedboard one, uncompress it and write it to an sd card. Be sure
>>>> to unmount (not eject) the sd card and run:
>>>>
>>>> sudo dd if=sdimage-8G-zedboard.direct of=/dev/sdX
>>>>
>>>> where sdx is the device the sd card is on.
>>>>
>>>> Philip
>>>>
>>>>>
>>>>> to get a working image with gnu radio for my zedboard.
>>>>>
>>>>> Unfortunately I can't get the board to boot with this image. I was
>>>>> wondering if someone can help me.
>>>>>
>>>>> what I tried so far ( all failed - can't boot from the SDCard):
>>>>>
>>>>> - default settings in the instructions
>>>>> - renaming u-boot.bin to boot.bin
>>>>> - renaming u-boot.bin to BOOT.BIN
>>>>> - renaming uImage--zedboard-zynq7.dtb to devicetree.dtb
>>>>> - I tried command line as well as gparted gui.
>>>>>
>>>>> what I checked:
>>>>>
>>>>> - download a linux from XillyBus and boot the board with SDCard ->
>> works
>>>>>
>>>>> v/r
>>>>> Alireza
>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Discuss-gnuradio mailing list
>>>>> address@hidden
>>>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>>>>
>>>>
>>>
>>
>