[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
RE: [Bayonne-devel] Placing an outgoing call on an available trunk.
From: |
Julien Chavanton |
Subject: |
RE: [Bayonne-devel] Placing an outgoing call on an available trunk. |
Date: |
Tue, 3 May 2005 11:44:14 -0400 |
You must define the trunk in bayonne.conf
Here is an example with 10 T1's, with E1's there is 30 channels not only
23.
Then you can write the command "start trunk1 myScript" in bayonne.ctrl
the bayonne FIFO.
[trunks]
; Specify the name of additional trunk groups to load
groups = trunk1 trunk2 trunk3 trunk4 trunk5 trunk6 trunk7 trunk8 trunk9
trunk10
[trunk1-trunks]
trunks = 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22
[trunk2-trunks]
trunks =
23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45
[trunk3-trunks]
trunks =
46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68
[trunk4-trunks]
trunks =
70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92
[trunk5-trunks]
trunks =
93,94,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112
,113,114
[trunk6-trunks]
trunks =
115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132,
133,134,135,136,137
[trunk7-trunks]
trunks =
138,139,140,141,142,143,144,145,146,147,148,149,150,151,152,153,154,155,
156,157,158,159,160
[trunk8-trunks]
trunks =
161,162,163,164,165,166,167,168,169,170,171,172,173,174,175,176,177,178,
179,180,181,182,183
[trunk9-trunks]
trunks =
184,185,186,187,188,189,190,191,192,193,194,195,196,197,198,199,200,201,
202,203,204,205,206
[trunk10-trunks]
trunks =
207,208,209,210,211,212,213,214,215,216,217,218,219,220,221,222,223,224,
225,226,227,228,229
-----Original Message-----
From: address@hidden
[mailto:address@hidden
g] On Behalf Of Lachlan Ross
Sent: May 2, 2005 9:48 PM
To: Bayonne Devel Mailing List
Subject: [Bayonne-devel] Placing an outgoing call on an available trunk.
Hi Everyone,
When using Bayonne to dial out, must you specify the trunk that the call
goes out on?
ie:
bayonne --control start 1 myScript
This sends the call out on trunk 1. What happens if trunk 1 already has
a call on it?
Can you some how place an outgoing call and have it just find an
available trunk?
Thanks for any ideas.
Lachlan
_______________________________________________
Bayonne-devel mailing list
address@hidden
http://lists.gnu.org/mailman/listinfo/bayonne-devel