[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [avrdude-dev] Adding support for ATmega32C1 in avrdude.conf
|
From: |
Joerg Wunsch |
|
Subject: |
Re: [avrdude-dev] Adding support for ATmega32C1 in avrdude.conf |
|
Date: |
Fri, 18 Jan 2013 22:56:28 +0100 |
|
User-agent: |
Mutt/1.5.20 (2009-06-14) |
As Stuart Cording wrote:
> Give me a couple of days and I'll send my config file and the serial
> date transfer log. Perhaps you will see something in the protocol
> exchange that I don't.
Seeing the log would be interesting, indeed.
> Do you have experience with optiboot as the firmware for the MCU
> boot loader?
Sorry, I personally don't have much experience with bootloaders at
all. If I had to use one, I'd probably start out with something that
implements STK500v2.
As Stuart Cording wrote:
> Attached is my modified avrdude.conf file.
#------------------------------------------------------------
# ATmega32c1
#------------------------------------------------------------
part
id = "m32c1";
# SMC
Well, please don't append that kind of metadata into the file itself.
Once committed to SVN, your name will be recorded in the commit
message (and in the file ChangeLog as well).
You are apparently using TAB characters in the assumption they were 4
positions per TAB. Everything else in AVRDUDE uses TABs as 8
positions per TAB. It's probably best to not use TAB characters
alltogether to avoid that kind of discrepancy.
desc = "ATMEGA32C1";
has_jtag = no;
has_debugwire = yes;
has_pdi = no;
has_tpi = no;
Basically, only "has_debugwire" needs to be mentioned, as all the
other methods default to "no" anyway.
stk500_devcode = 0x82;
Btw., the AVR Studio 4 XML file for this devices mentions 0x66, I just
noticed.
#avr910_devcode = 0x74;
signature = 0x1e 0x95 0x86;
pagel = 0xd7;
OK
bs2 = 0xa0;
That ought to be 0xE2 (as PE2 is the "BS2" line).
"pagel" and "bs2" are only used by the genuine STK500 in the
high-voltage parallel programming algorithm when running with firmware
version 1. Not much relevance anymore today. I guess all STK500s are
running V2 firmware these days, the STK500v1 protocol only survived in
some bootloaders (but they don't deal with parallel programming).
chip_erase_delay = 9000;
That matches the datasheet, however, the XML file only claims 45 µs.
I'd stay with the 9000 though, to be on the safe side.
pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
"x x x x x x x x x x x x x x x x";
chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
"x x x x x x x x x x x x x x x x";
timeout = 200;
stabdelay = 100;
cmdexedelay = 25;
synchloops = 32;
bytedelay = 0;
pollindex = 3;
pollvalue = 0x53;
predelay = 1;
postdelay = 1;
pollmethod = 0;
According to the XML file, pollmethod should be set to 1.
pp_controlstack =
0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
hventerstabdelay = 100;
progmodedelay = 0;
latchcycles = 5;
togglevtg = 1;
poweroffdelay = 15;
resetdelayms = 1;
resetdelayus = 0;
hvleavestabdelay = 15;
chiperasepulsewidth = 0;
chiperasepolltimeout = 10;
programfusepulsewidth = 0;
programfusepolltimeout = 5;
programlockpulsewidth = 0;
programlockpolltimeout = 5;
idr = 0x31;
spmcr = 0x57;
allowfullpagebitstream = no;
"allowfullpagebitstream" is only relevant for JTAG.
memory "eeprom"
paged = no; /* leave this "no" */
page_size = 4; /* for parallel programming */
size = 1024;
min_write_delay = 9000;
max_write_delay = 9000;
readback_p1 = 0xff;
readback_p2 = 0xff;
read = " 1 0 1 0 0 0 0 0",
" 0 0 x x x a10 a9 a8",
" a7 a6 a5 a4 a3 a2 a1 a0",
" o o o o o o o o";
write = " 1 1 0 0 0 0 0 0",
" 0 0 x x x a10 a9 a8",
" a7 a6 a5 a4 a3 a2 a1 a0",
" i i i i i i i i";
loadpage_lo = " 1 1 0 0 0 0 0 1",
" 0 0 0 0 0 0 0 0",
" 0 0 0 0 0 0 a1 a0",
" i i i i i i i i";
writepage = " 1 1 0 0 0 0 1 0",
" 0 0 x x x a10 a9 a8",
" a7 a6 a5 a4 a3 a2 0 0",
" x x x x x x x x";
mode = 0x41;
delay = 10;
blocksize = 128;
readsize = 256;
;
memory "flash"
paged = yes;
size = 32768;
page_size = 128;
num_pages = 256;
min_write_delay = 4500;
max_write_delay = 4500;
readback_p1 = 0xff;
readback_p2 = 0xff;
read_lo = " 0 0 1 0 0 0 0 0",
" 0 a14 a13 a12 a11 a10 a9 a8",
" a7 a6 a5 a4 a3 a2 a1 a0",
" o o o o o o o o";
read_hi = " 0 0 1 0 1 0 0 0",
" 0 a14 a13 a12 a11 a10 a9 a8",
" a7 a6 a5 a4 a3 a2 a1 a0",
" o o o o o o o o";
loadpage_lo = " 0 1 0 0 0 0 0 0",
" 0 0 x x x x x x",
" x x a5 a4 a3 a2 a1 a0",
" i i i i i i i i";
loadpage_hi = " 0 1 0 0 1 0 0 0",
" 0 0 x x x x x x",
" x x a5 a4 a3 a2 a1 a0",
" i i i i i i i i";
writepage = " 0 1 0 0 1 1 0 0",
" 0 a14 a13 a12 a11 a10 a9 a8",
" a7 a6 x x x x x x",
" x x x x x x x x";
mode = 0x21;
XML says 0x41
delay = 6;
XML says 10
blocksize = 256;
XML says 128
readsize = 256;
;
memory "lock"
size = 1;
read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
"x x x x x x x x x x o o o o o o";
write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
"x x x x x x x x 1 1 i i i i i i";
min_write_delay = 9000;
max_write_delay = 9000;
;
memory "lfuse"
size = 1;
read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
"x x x x x x x x o o o o o o o o";
write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
"x x x x x x x x i i i i i i i i";
min_write_delay = 9000;
max_write_delay = 9000;
;
memory "hfuse"
size = 1;
read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
"x x x x x x x x o o o o o o o o";
write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
"x x x x x x x x i i i i i i i i";
min_write_delay = 9000;
max_write_delay = 9000;
;
memory "efuse"
size = 1;
read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
"x x x x x x x x o o o o o o o o";
write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
"x x x x x x x x 1 1 1 1 1 i i i";
min_write_delay = 9000;
max_write_delay = 9000;
;
memory "signature"
size = 3;
read = "0 0 1 1 0 0 0 0 x x x x x x x x",
"x x x x x x a1 a0 o o o o o o o o";
;
memory "calibration"
size = 1;
read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
"0 0 0 0 0 0 0 0 o o o o o o o o";
;
;
--
cheers, J"org .-.-. --... ...-- -.. . DL8DTL
http://www.sax.de/~joerg/ NIC: JW11-RIPE
Never trust an operating system you don't have sources for. ;-)